number 2 The following information is given for a 320KW 600V long shunt flat compoundgenerator, when the machine delivering rated load:RA0.0262,RF -80Ω, Rs0.0152, Rp = 0.0382 and the commutating fieldwinding resistance Rc = 0.0122. Calculate the Induced voltage and Power generated bythe armature.

In the question, Dc long shunt compound Generator have all parameters. Find the induced voltage…

Answered: The following information is given for…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A 4-quadrant DC chopper with bipolar switching operating at a switching frequency of 2kHz, is connected to a 120VDC source (Vs) and a DC motor which has a counter EMF (CEMF) of 50VDC at rated speed. The armature resistance is 2Ω and the armature inductance is 20mH. Calculate: a) Output voltage with an 80% duty cycle b) Magnitude and direction of the DC armature current with an 80% duty cycle. c) Duty cycle for a forward braking current of 10ADC. (Assume the speed has not changed due to the large inertia of the load.)
A shunt generator supplies a 30kW load at 215V through cables of resistance, R = 110mn. If the field winding resistance, Rf =680 and the armature resistance, Ra =45mn. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
Suppose a shunt regulator voltage is 250V, the armature current is 30A. field coils are required to provide an MMF of 500AT. The field might typically say 200turns with resistance of 0.5Ohms/turn. Find the dissipated power as heat and total input required and the efficiency
analyze 3 commonly used ac motor starting methods using suitable diagrams and torque-speed curves
A separately excited motor runs at 1045rpm, with a constant field current, while taking an armature current of 50A at 120V. The armature resistance is 0.1 Ω if the load on the motor changes such that it now takes 95A at 120V, determine the motor speed at this load.
The armature, series field and shunt field resistances of a 125kW, 250V long shunt cumulative compound dc generator are 0.025-ohm, 0.01 ohm and 30 ohms, respectively. If the stray power loss at rated load is 5kW, determine the motor brake horsepower required to drive this machine. Assume a brush drop of 2V and a stray load loss of 1% of the output.
A separately excited generator has no-load voltage of 125V. A certain load rated at 1200W, 120V is then connected at the terminal. Calculate the series resistance needed to connect to the armature circuit in order for the load to operate at rated condition if the armature resistance is 0.0692Ω.
Explain the concept of motherboard power delivery and voltage regulation. How does the quality of power delivery components (e.g., VRMs) impact the stability and overclocking potential of a system?
[Electrical Machines and Power System] Discuss two design considerations when selecting a stepper motor.
Describe the merits of buckhholz relay
A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
Describe the main advantage of GTO over thyristor.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning