The force F =84 N acts on the end of the pipe at B. (Figure 1) Part B Determine the magnitude of the maximum moment of the force F about point A. Express your answer to three significant figures and include the appropriate units. HA MA max Value Units Figure 1 of 1 Submit Request Answer Part C Determine the angle 0min (0°< Omin <180°) of the force F that will produce minimum moment about point A. 0.9 m Express your answer using three significant figures. F VO AZO vec -0.3 m-- -0.7 m Oin P Pearson 13:1 22.04.2

The force F =84 N acts on the end of the pipe at B. (Figure 1) Part B Determine the magnitude of the maximum moment of the force F about point A. Express your answer to three significant figures and include the appropriate units. HA MA max Value Units Figure 1 of 1 Submit Request Answer Part C Determine the angle 0min (0°< Omin <180°) of the force F that will produce minimum moment about point A. 0.9 m Express your answer using three significant figures. F VO AZO vec -0.3 m-- -0.7 m Oin P Pearson 13:1 22.04.2

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 34P: In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the...

See similar textbooks

Similar questions

overhead view of a rigid rod that turnsabout a vertical axle until the identical rubber stoppers A and B are forced against rigid walls at distances rA = 7.0 cm and rB = 4.0 cmfrom the axle. Initially the stoppers touch the walls without beingcompressed.Then force of magnitude 220 N is applied perpendicularto the rod at a distance R = 5.0 cm from the axle.Find the magnitudeof the force compressing (a) stopper Aand (b) stopper B.
A uniform slender rod of length L = 36 in. and weight W = 4 lb hangs freely from a hinge at A. If a force P of magnitude 1.5 lb is applied at B horizontally to the left (h = L), determine (a) the angular acceleration of the rod, (b) the components of the reaction at A.
In using the spring scale to find the equilibrant, why does one hold it horizontally on its body and not on its (topmost) handle?
Which of the following statement/s is/are accurate? For non-uniform body, the center of gravity is at the geometric center. In equilibrium, the net moment of force at the center of gravity is zero. For uniform body, the center of gravity and centroid act on the same point. The center of gravity is always at the geometric center.
A spade is modelled as a uniform rod, of mass 2kg and length 90cm, attached to a uniform square lamina, of side 20cm and mass 0.5kg. A gardener holds the spade horizontally with hands 30cm and 60cm from the end of the rod. Find the vertical forces exerted by the gardener's hands. Im stuck on this q, pls help.
If torque is a vector, with a specific direction in space, what is meant by clockwise and counterclockwise torques? If the sums of these torques on a rigid body are equal, what does this imply physically?
Consider a bar of length 5.5 m, being acted on by three forces and constrained to rotate about its left end. The magnitudes of the first two forces are 19 N and 26 N and the first force is acting on the end of the bar at an angle of 53 What is the torque in newton-meters, due to F1 on this bar relative to the left end? What is the torque in newton-meters, due to F2 on this bar relative to the left end, if this force is acting at the midpoint of the bar? Use a coordinate system with positive directed out of the screen. What is the magnitude of the force F3, in newtons, if the force is a distance 0.25 m from the left end and the bar is not rotating?
A strut of lengthL = 3.00 m and mass m =16.0 kg is held by a cableat an angle of θ = 30.0°with respect to the horizontalas shown in FigureP8.30. (a) Sketch a forcediagram, indicating allthe forces and their placementon the strut. (b) Why is the hinge a good place to usefor calculating torques? (c) Write the condition for rotationalequilibrium symbolically, calculating the torques around thehinge. (d) Use the torque equation to calculate the tension in the cable. (e) Write the x- and y-components of Newton’ssecond law for equilibrium. (f) Use the force equation tofind the x- and y -components of the force on the hinge.(g) Assuming the strut position is to remain the same, wouldit be advantageous to attach the cable higher up on the wall?Explain the benefit in terms of the force on the hinge andcable tension.
A block of mass m rests on a slope, at an angle (theta_, and is attached by a string of negligible mass to a solid drum of mass M and radius R, as shown in the figure. When released, the block accelerates down the slope at rate a. a) Use the rotational form of Newton’s 2nd law (i.e. the net torque onthe system) to find the tension in the cable. b) Use Newton’s 2nd law (i.e. the net force on the system) to find thecoefficient of friction c) Using the expression found in part b) what is the acceleration of theblock if the slope is frictionless and the drum is massless?
What three factors affect the torque created by a force relative to a specific pivot point?
A uniform rod of mass and length is held vertically by two strings of negligible mass, as shown below. (a) Immediately after the string is cut, what is the linear acceleration of the free end of the stick? (b) Of the middle of the stick?
In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?