The friction at sleeve A can provide a maximum resisting moment of 380 Nm about the <-axis. Determine the largest magnitude of force F that can be applied to the bracket so that the bracket will not rotate about the x-axis. Given that L1 is 275 mm, L2 is 171 mm and L3 is 126 mm. Z F 60° L1 mm A B 45° 60° L3 mm L2 mm y

The friction at sleeve A can provide a maximum resisting moment of 380 Nm about the <-axis. Determine the largest magnitude of force F that can be applied to the bracket so that the bracket will not rotate about the x-axis. Given that L1 is 275 mm, L2 is 171 mm and L3 is 126 mm. Z F 60° L1 mm A B 45° 60° L3 mm L2 mm y

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the magnitude of the pin force at A.Assume W = 665 lb, a = 3.7 ft, b = 2.9 ft, r = 8 in.
The disk clutch is used in standard transmissions of automobiles. If four springs are used to force two plates A and B together, determine the force in each spring required to transmit a moment of M = 600lb-ft across the plates. The coefficient of static friction between A and B is u, = 0.3.
The left and right strings have a mass of 0.01 kg, the middle string has a mass of 0.02 kg. Both theta and beta angles are 40 degrees. Show the calculations used to determine the horizontal and vertical components of the tension forces connected to the center string.
The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes through a ring C with negligible friction and is attached to hooks at E and F. Knowing that the frame supports a uniformly distributed load of 1500 N/m along segment AB, do the following.1) Shows the correct vector representation of the resultant of the two tension forces acting at ring C. Note that T_CF = T_CE = T2) Explain along which line/axis you can sum moments to generate an equilibrium equation with only the magnitude of the tension force as the unknown. Explain your choice.3) Find the magnitude of the tension force.
The device shown is a part of an automobile seat-back-release mechanism. The part is subjected to the 7.6-N force exerted at A and a 250-N·mm restoring moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. Your answer will be positive if the intercept is above O and negative if below O.
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule
117 The right-angle pipe OAB of Prob. 2/99 is shown again here. Replace the 750-N tensile force which the cable exerts on point B by a force-couple system at point O. Ans. R --5981 + 411j + 189.5k N Mo = -361i - 718j + 419k N m 1.2 m C 1.6 m 0.7 m 30 0.8 m Problem 2/117 2/118 In an afte
When a 6 kg load is hung at point O and member AO is adjusted until it is horizontal, the angle is measured to be 35 Determine the final readings of spring scales S_{1} and S_{a} and solve for the moments they produce about each of the axes passing through A and B if member AB is measured to be 38 cm.
Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of 565 lb in the y-direction, determine the necessary values of T and θ.Assume F1 = 330 lb, F2 = 240 lb, F3 = 430 lb, ϕ= 29°.
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
The ideal spring of constant k=2.6kN/m is attached to the fitted at point A and the end fitted at point B, as shown. The spring is unstretched when theta(A) and theta(B) are both zero. If the fitted is rotated 15⁰ clockwise and the end fitting is rotated 30⁰ counterclockwise, determine the vector expression for the spring force F. Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m
The 12ft pole AC (negligible mass) lies in the y-z plane and forms a 30° angle with the z-axis. The pole is held in place at point C by a ball-and-socket joint. Two cables, BD and BE, are fixed to the pole at point B (these represent two separate cables attached at B). A 110 lb force pulls downward at the end of pole AC in the vertical direction (y-direction). If the distance between B and C along the feet, determine the Reactions at C (ball-and-socket joint) The tension in cables BD and BE.