Hello pls write this on white page ASAP just copy this whole on white page I'll UPVOTE Write the forces in vector form,F = 55 iF = F; (- sin a î + cos a j)F = 130 (- sin 65° î + cos 65° j)F =-117. 82 î + 54. 94 jF = Fs (- cos e î + sin e j)F = 55 x (- cos 54. 211° i + sin 54. 211°)F = 32. 164 i + 44. 614 jStep 3The resultant force is,F =F +F +FF = 55 i - 117. 82 î + 54. 94 j + 32. 164 î + 44. 614 ĵF = -30. 656 î + 99. 554Calculate the magnitude of the resultant force,F= V(-30. 656)2 + (99. 554)²F = 104. 167 Ib,The direction of the resultant force is,99.554tan o =-30.6566 = tan 9.3544 = -72. 885'Drawing the force polygon is,F,F_F.54.211°-65072.885°F Step 1Given that,F, = 55 lbsF2 = 130 lbsF = 55 lbsa = 65°n = 8.6m = 6. 2The given system of forces is,F2F3mF1Step 2tan e = 4tan 0 = 00 = tan- (0 = 54. 211°

Answered: Image /qna-images/answer/3d987141-36ea-4f85-8c2f-5d823ffcfd78.jpg

Answered: The given system of forces is, F2 F3 m

Engineering

Mechanical Engineering

The given system of forces is, F2 F3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
.A belt 200 mm wide and 7 mm thick drives a pulley at belt speed of 25 m/s. The density of the belt is 980 kg/m3 and the coefficient of friction between the belt and pulley is 0.23. Given that the angle of contact of pulley is 2π/3 and the allowable stress of the belt is 1.8 MPa, determine the tension on the slack side of the belt (T2) in N
A hydraulic crane has a small piston diameter of 10 mm and a large piston diameter of 8 cm. After the point of impact of the direct force from the axis of the mechanical crane is 24 mm, while the point of impact of the indirect force from the axis of the mechanical winch was 6.4 cm. It was used to lift a load of 18 tons. Required: 1- Draw a diagram For the crane 2- hydraulic advantage 3- mechanical benefit 4- direct force 5- external force 6- general mechanical benefit 7- if the load increases by 30% calculate the direct force and external force in this case 8- Calculate the diameters of the crane necessary to lift a load of 15 tons With the same external force as the original, noting that the maximum diameter of the small piston is not more than 18 mm.
In machine design we usually compare the equivalent stress of the component with the: a) Allowable stress b) Machine stress c) Force d) Moment e) Torque
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
Note: kindly give me both answers.. A transmission cable 300 m long, weighs 600 kg. The tensions at the ends of the cable are400 kg and 450 kg. Find the distance of its lowest point to the ground. A. 145 m B. 150 m C. 153 m D. 148 m Answer is 150 m.. Show me the work The tip to tail addition of vector is also referred to as A. Parallelogram law B. Triangle law C. Trigonometry D. Square rule
5 - note: ignore weight of the bar.A) ( - 6/7)T(CB) + A(y)=0 (A=reaction force at A, A(x), A(y), A(z) are components of force A)B) (2/7)T(CB)+A(x)=392 (A=reaction force at A, A(x), A(y), A(z) are components of force A)C) A(x)=2A(y) (A=reaction force at A, A(x), A(y), A(z) are components of force A)D) A(x)=5A(z) (A=reaction force at A,A(x), A(y), A(z) are components of force A)
Suppose that P1 = 5.6 kN and P2 = 4.2 kN Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) FGF b) FCF c) FCD
P2 = 18.95 Psi T2 = 575 R W12 = 32.59 Btu Q12 = 0 Btu
14. A bottle with a lid contains 0.0083kg of air at 64°C. If the volume of the air inside the bottle is 0.007m3 and the diameter of the lid is 0.35m, what will be the force required to close the lid? a. 11.4714kN b. 11.0385kN c. 11.7382kN d. 11.7035kN
Given the lifting table shown below , The diameter of the plunger DP 8 cm.The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm c) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8cm .
Question 2) As shown in the figure, two blocks of 4kg and 8kg are tied together on two inclined planes with a rope passed through a frictionless reel. The friction between the 4kg mass and the surface and the friction coefficient is 0.15. (The distance between g = 10 m / s2 and A-B is 30 m.) a) Find the magnitude and direction of the acceleration of each block. b) Find the tensions in the rope. c) Using energy conservation, find the speed of the 8kg mass when the 4kg mass moves from A to B. d) Calculate the change in 4kg mass kinetic energy.