The head of a 300 mm diameter cylinder vessel will be designed. The internal pressure in the cylinder is Pin = 1MPA. The bolts have initial tightening load of 12 kN. a) Find the stiffness of the bolt and members. b) Determine the number of bolts (N) for a safety factor of 2 for fatique loading.

The head of a 300 mm diameter cylinder vessel will be designed. The internal pressure in the cylinder is Pin = 1MPA. The bolts have initial tightening load of 12 kN. a) Find the stiffness of the bolt and members. b) Determine the number of bolts (N) for a safety factor of 2 for fatique loading.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: iven a 1.3meter Wide Flange steel compression member with A=4,118mm2, Ix=87,958,354mm4 and…

Q: A collar is fitted as a tight fit on a solid shaft. made before assembly in measuring, the outer…

A: given data; ⇒outer diameter of the ring (do)=159.97mm⇒inner diameter of the ring (di)=100.03mm⇒outer…

Q: A steel wheel of 800mm diameter on a horizontal steel rail. It carries a load of 60ON. The…

A: We have to calculate rolling force

Q: - 62.5 mm - Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm…

Q: 1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the…

Q: The one end of a hollow square bar whose side is 10.17 with thickness is 1.17 under a tensile stress…

Q: A 4-T crane is used to lift a 3m x 1.2m x 200mm pre-cast panel. A spreader beam is needed to ensure…

Q: Question 1. P T. The figure (not drawn to scale) shows a cylindrical column submitted to a combined…

A: as per guidelines i have to solve only first part of your question

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height…

A: Note:- As per our company guidelines we are supposed to answer only the first three sub-parts.…

Q: Calculate the maximum stress affecting a bolt by specifying which Bolts will have the maximum stress…

Q: For the assembly shown, a yoke on a 30 mm diameter rod is attached to a 25 mm thick bracket via 15…

Q: A flange coupling with bolt circle of 250 mm uses 8 bolts, 25 mm diameter, the torque transmitted is…

A: Given Data The diameter of the bolt circle is D=250 mm. The number of bolts are n=8. The diameter…

Q: A column supports a compressive load of 360KN. Determine the outside diameter of column if inside…

Q: Given a 2meter Wide Flange steel compression member with A=4,513mm2, Ix=86,630,006mm4 and…

Q: The one end of a hollow square bar whose side is 10.68 in with 1.68 in thickness is under a tensile…

Q: The crankpin of an engine sustains a maximum load of 35 kN due to steam pressure. If the allowable…

Q: A steel wheel of 900mm diameter on a horizontal steel rail. It carries a load of 50ON. The…

A: GIVEN DATA - W=500N D=900mm SO R=450mm μ=0.1 WE HAVE TO FIND VALUE OF FORCE

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

Q: The one end of a hollow square bar whose side is (10.13) in with (1.13) in thickness is under a…

Q: 1. A tensile load of 5.00 kN is applied to a square bar 12 mm on a side and having a length of 1.65…

A: In the given example we have to find the values of the Youngs modulus and yield strength from the…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Q: The one end of a hollow square bar whose side is 10.17 in with 1.17 in thickness is under a tensile…

A: Calculate the area of the hollow square bar.

Q: PROVIDE FREE-BODY-DIAGRAM IN EVERY LETTER. Show clear hand writing and complete solution. Thank you…

A: Given: The load, P = 275 kN

Q: Question: 35 35 The one end of a hollow square bar whose side is (10 +) in with (1 +) in thickness…

Q: Q3. A welded steel cylindrical drum made of a 15mm thickness plate has an internal diameter of 1.50…

Q: The figure shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A: Given details: P=20 kNd=10 mmζy=300 MPan=2

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Q: 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850…

A: Given: The maximum torque is 850 in-lb. The diameter of the shaft is 1.75 in. Ultimate stress is…

Q: Q1 / Find the minimum bolt diameter and the minimum thickness ofeach yoke that will support a load…

A: Write the expression for the load. Here, τ represents the shear stress, Abolt represents the area…

Q: The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are…

A: Given: From tables of data:grip l=1.50 inchesnut thickness=35/64 in.we have to add two threads…

Q: Calculate the riveted joints, find its efficiency and draw a suitable sketch. Thickness of the…

A: Another name of rivet joint is lozenge joint. Selection of material σt=80 mpaζ=65 mpaσc=160 mpa

Q: 3. Problem 2: The lap joint is fastened with four rivets. If the working stress is 14 ksi (kips per…

Q: A collar is fitted as a tight fit on a solid shaft. made before assembly in measuring, the outer…

A: Shaft collars are ring-shaped plastic or metal devices that clamp around a shaft and are commonly…

Q: Find factor of safety if the Ultimate Stress of a ductile material is 250.94 MPa. If the material is…

Q: Problem-based learning - Acquire enhanced problem-solving skills using critical thinking Two shaft…

A: Given data: The diameter of the shafts is d = 35 mm The number of bolts is n = 8The diameter of the…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

Q: A 1000mm cast iron pulley is fastened to a 112mm shaft by means a 28mm square key 160mm long. The…

A: given data :- shear stress = 200Mpa bearing stress = 660 Mpa length of key = 160 mm width and…

Q: An eye bolt carries a tensile load of 20kN.Find the size of the bolt(in mm), if the tensile stress…

Q: 1. An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder…

Q: A metal tube with inside diameter of 100mm is subjected to a tensile lad of 500kN. Find the outside…

A: Inside diameterdi=100 mm di=0.1 m Outside diameter=do Tensile loadP=500…

Q: The allowable tensile stress for a ½ bolt of thread length 7/32 inches is 30000 psi. The allowable…

Q: A mild steel cover plate is to be designed for an inspection hole in the shell of a pressure…

A: Given Hole diameter = 120 mm Internal pressure = 6 N/mm2 Cover plate tensile stress = 60 MPa Bolt…

Q: ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined…

A: P=30kN d1=9mm d2=22mm d3=14mm

Q: 8- A steel bar of diameter 1 cm and length of 10 cm is made of steel with E= 200 Gpa and yield…

A: To find: The maximum tensile force. Given: The diameter of steel bar is d=1 cm. The length of steel…

Q: Requlred Information A rotating shaft of 25-mm diameter is simply supported by bearing reaction…

Q: A collar is fitted as a tight fit on a solid shaft. made before assembly in measuring, the outer…

A: Shaft collars are ring-shaped plastic or metal structures that clamp around a shaft and are…

Q: A steel rod on a bridge must be made to withstand a pull of 6000 Ibs. Find the diameter of the rod…

Q: A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

The head of a 300 mm diameter cylinder vessel will be designed. The internal pressure in the
cylinder is Pin = 1MPA. The bolts have initial tightening load of 12 kN.
a) Find the stiffness of the bolt and members.
b) Determine the number of bolts (N) for a safety factor of 2 for fatique loading.
IMPA
D= 300 mm
M 10 1.5 grade 5.8
cast iron
E= 200 GPa
Eci= 90 GPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A coil spring is to be used for the front spring of an automobile. The spring is to have a rate of 2757 kPa., an inside diameter of 10.3 cm., and a free length of 35.9 cm., with squared-and-ground ends. The material is to be oil- tempered chrome vanadium Decide upon the diameter of the wire and the number of free coils for a design load of F  1500 lb . Be sure “solid stress” is all right. How much is the pitch angle?
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
A single L8x6x1/2 (A36 steel) is used as a tension brace in a multi-story building. The 8 inch leg of the angle is attached to a gusset plate with two lines of four ¾ inch Ø bolts at a spacing of 3 inches. Determine the shear lag factor (consider Case 2 & 8) and the effective net area. Considering yielding and net section rupture, determine the design strength by LRFD and the allowable strength by ASD. (PLEASE SOLVE THIS ONE WITH THE BOLD TEXT)
A flange coupling connects two 2” diameter shafts. The flanges are fitted with 6 bolts of SAE 1040 steel on a 7” bolt circle. The shafts runs at 300 rpm and transmits 45 hp. Assume a factor of safety of 5, ultimate tension of 70,000 psi, and ultimate shear of 55,000 psi. Determine: a) The torque transmitted, in-lbs b) The force applied per bolt, lbs c) The diameter of the bolt required, in d) The thickness of flanged to be used, in
A semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.
Q - 4) In buckling experiment a steel column ( E - 210 Gpa ) was examined in pin - fixed method . It endured a load up to 1190 N. Its length is 600 mm cross sectional width is 20 mm , thickness is 4 mm. Find the critical stress and compare it with the actual stress (error %).
A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of 3000 lb. If the material is AISI 1015, cold drawn, find the factor of safety based on ultimate strengths of a. the threaded shank, b. the head against being sheared off, and c. the bearing surface under the head. d. Is there any need to consider the strength of standard cap-screw heads in design?
A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of 3000 lb. If the material is AISI 1015, cold drawn, find the factor of safety based on ultimate strengths of a.the threaded shank, b.the head against being sheared off, and c.the bearing surface under the head. d.Is there any need to consider the strength of standard cap-screw heads in design?
Draw FBD and determine Stress and Safety Factor of Bicycle Axle (Thru Axel) Specification Weight of cyclist = 120 kg. Materials: Aluminum alloy (AL 6061-T6) Dimension: Length = 122 mm, Diameter = 12 mm, Thread pitch = 1.75 mm, Thread Length = 16 mm.
A mild steel cover plate is to be designed for an inspection hole in the shell of a pressure vessel. The hole is 120 mm in diameter and the pressure inside the vessel is 6 N/mm2. Design the cover plate along with the bolts. Assume allowable tensile stress for mild steel as 60 MPa and for bolt material as 40 MPa
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
Determine the strength of the bedrock granite. Assume you sampled the granite where it was exposed at the surface and ran a series of 4 triaxial compression tests (results given below). Determine the Coloumb coefficient (or friction angle) and the cohesion of the rock given these test results. Either use graph paper to draw Mohr’s circles and a failure envelope to help you determine these values or use the computer to make a plot. Show all your work for credit! Test Confining pressure Axial load at failure 1 4.5 MPa 35.5 MPa 2 9 MPa 50 MPa 3 17 MPa 73 MPa…