The homogeneous rectangular plate weighs 40 lb and is supported in a vertical plane by the light parallel links as shown. If a couple M = 80 lb ft is applied to the end of link AB with the system initially at rest, calculate the force supported by the pin at C as the plate lifts off its support with 0 = 30°. 24"

The homogeneous rectangular plate weighs 40 lb and is supported in a vertical plane by the light parallel links as shown. If a couple M = 80 lb ft is applied to the end of link AB with the system initially at rest, calculate the force supported by the pin at C as the plate lifts off its support with 0 = 30°. 24"

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.45P

See similar textbooks

Similar questions

The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide.
The figure is a model for member CDE of the frame described in Prob. 4.10. Draw the FBD of the member, neglecting its weight. Count the unknowns.
Can the uniform bar of weight W remain at rest in the position shown?
a trolley of mass m stands on frictionless rails.a rod of mass m and length l is pivoted to the roof of trolley on a frictionless hinge and the and rod is gently left from the horizontal postion as shown in the figure. initialy the whole system was at rest when the rod becomes vertical for the first time.net vertical force offered by the track to the carriage is 16/x mg. find x.
A uniform slender bar AB with a mass of 20 kg and length of 3.6 m leans on a wall as shown. It is attached to a weightless small roller at end A on a smooth horizontal surface. The coefficient kinetic friction between end B and the wall is 0.25. If the bar is released from rest in the position shown when θ is 30°. Then find, determine the normal force at A. determine the normal force at B. determine the frictional force between end B and the wall.
Find the force P required to pull the 40-kg homogeneous roller with radius 720mm over the 90-mm curb.
The body A with a mass of 50 kg is in equilibrium with the help of the pulling force generated in the AB and AC cables in the middle of the inclined plane and the friction force between the curved surface and the object. The friction force is on the line of motion of body A and develops in the opposite direction to the movement in the direction of the arrow shown in the drawing. Since the pulling force in AB and AC cables is 15.1 and 22.1 N, respectively, calculate the balancer friction force acting on the object vectorially? (g = 9.81 m / s'2)
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)
The 136-kg industrial door with mass center at G is being positioned for repair by insertion of the 6° wedge under corner B. Horizontal movement is prevented by the small ledge at corner A. The coefficients of static friction at both the top and bottom wedge surfaces are 0.58. Calculate the rightward force P' which would remove the wedge from under the door. Assume that corner A does not slip for your calculation of P, but then check this assumption; the coefficient of static friction at A is 0.58.
When the 0.05-kg body is in the position shown, the transitional spring at O is pretensioned so as to exert a 0.75-Nm clockwise moment of the body. Determine the force P required to break at contact C. Complete solutions for (a) including the effect of weight and (b) neglecting the weight.
A ball is shot at high speed into a frictionless channel that is in the shape of a segment of a circle with center at O.The channel is frictionless and sits on a horizontal table top.The figure shown is the top view.Which of the following force(s) are acting on the ball when it is within the frictionless channel at position B? Explain your answers.Check all that apply.1- A downward force of gravity.2- A force pointing from O to B.3- A force in the direction of motion.4- A force pointing from B to O.