The inner conductor of a coaxial cable has a diameter of 0.5 mm, an outer conductor an inner diameter of 6 mm and a length of 50 m. If the inner and outer conductors of the coaxial cable will be joined at one end of the cable, and if the permeability of the insulating material is µ = 4πx10^-7 H/m, what will be the inductance of the cable?

The inner conductor of a coaxial cable has a diameter of 0.5 mm, an outer conductor an inner diameter of 6 mm and a length of 50 m. If the inner and outer conductors of the coaxial cable will be joined at one end of the cable, and if the permeability of the insulating material is µ = 4πx10^-7 H/m, what will be the inductance of the cable?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter42: Heat Gains And Heat Losses In Structures

Section: Chapter Questions

Problem 10RQ: If the R-value of a construction material is 2.0, what isits U-value? A. 0.25 B. 0 50 C. 1.0 D. 2.0

See similar textbooks

Similar questions

5. A round aluminum sleeve with an outer diameter of 300 mm and an inner diameter of 200 mm is pressed onto a round steel sleeve with an inner diameter of 100 mm. The radial interference between the two sleeves is 6 = 0.25 mm. Let Ex = 72 GPa, VA = 0.33, E, = 200 GPa and v; = 0.29. Determine the following: (19 points) The interference pressure, p. in MPa between the two sleeves The change in the inner radius in the aluminum sleeve, u, in millimeters If the allowable tangential stress, do, in the aluminum is 180 MPa, determine the safety factor in the aluminum with respect to failure due to tangential stress. You may ignore the radial stres 7
Figure is a cross-sectional view of a coaxial cable. The center conductor is surrounded by a rubber layer, which is surrounded by an outer conductor, which is surrounded by another rubber layer. In a particular application, the current in the inner conductor I 2 is 6.00 A out of the page and the current in the outer conductor I 1 is 2.00 A into the page. Assume that l = 1.80 mm. Determine the magnitude and direction (upward or downward of the page) of the magnetic field at point b. (Choose upward of the page as the positive y-direction and express the magnetic field by using the sign of the result, which must be in µT and without decimals. That means if you get a result of a 922 and the direction of the field is upward of the page, just type 922 or if you find the direction of the field as downward of the page, just tpe -922 in the answer box. Maximum of 2% error is accepted in your answer. Take vacuum permeability µ 0 = 4π x 10 -7 T /A 2 and π = 3.14.)
A bimetallic strip is used as a sensor. The strip has a length of 20 μm. The width of the strip is 1μm. It has an upper layer made of steel (E = 210 x 10 9 N/m 2 ) and the lower layer made of aluminum (E = 80 x 10 9 N/m 2 ). Each layer is 0.1 μm thick. Determine the equivalent stiffness of the strip in the axial direction. Note that the strips are perfectly attached.
DC and AC subject: 1. Consider a wire carrying a current in the presence of a magnetic field, and a given flux density of 0.25 T. If the wire is 1.0 m long and carries a 0.5 A current, what is the magnitude of the force induced in the wire? 2. The wire shown is moving in the presence of a magnetic field. With the information given in the figure, determine the magnitude and direction of the induced voltage in the wire. (see the figure below)
A rod of semiconducting material of lenght L=3 m and cross-sectional area A=4.5 mm^2 lies along the x-axis between x=0 and x=L. The material obeys ohm's law, and resistivity varies along the rod according to p=p0 (1-(x^2/L^2)) where p0= 4.10^-4 ohm.m. The end of the rod x=0 is at a potential V0=30V greater than the x=L. A) what is the total resistance, in units of ohm, of the rod? B) what is the current, in units of miliamperes, in the rod? C) what is the electric potential, in units of Volt, in the rod at x=L/2? D) what is the electic-field magnitude E, in units of V/m, in the rod at x=L/2?
An electric train made up of two cars, each weighing50,000lb, is connected by couplings of stiffness equal to16,000lb/in., as shown in the figure below. Determine the natural frequency of the system.
A parallel-plate capacitor with plate separation of 2 mm has a 1kV voltage applied to its plates. If the space between its plates is filled with polystyrene (£r = 2.55),find E, P, and Pps · Assume that the plates are located at x = 0 and x = 2 mm.
Define the electrical power in terms of resistance R, current I, and potential difference V.
What is the resistance R of a length of copper wire whose length = 10 m and whose diameter = 0.10 mm?
The figure below shows a conducting rod sliding along a pair of conducting rails. The conducting rails have an angle of inclination of θ = 32.0 degrees. There is a resistor at the top of the ramp that connects the two conducting rails (R = 1.5 ohms). The mass of the rod is 0.43 kg. The rod starts from rest at the top of the ramp at time t = 0. The rails have negligible resistance and friction, and are separated by a distance L = 15.3 m. There is a constant, vertically directed magnetic field of magnitude B = 1.40 T. What is the rod's terminal speed?
The radius of a Van de Graaf generator that can collect a maximum charge of Q coulombs on its surface is given by R= 1.826 x 10-2 √Q. Solve the formula for Q and find Q for a generator with a radius of 1.5 m.
Calculate the strain experienced by a rod of length 2m subjected to a force that causes a change of resistance of 0.00002 Ω in the gauge Wheatstone bridge circuit. The strain gauge has gauge factor of 2 and the resistivity of the Wheatstone bridge circuit wires is 1.83 × 10-8 ohm-metre having a cross-sectional area 0.05m² and length 0.1m.