Wire C and wire D are made from the same material, having length LC = LD = 1.0 m and the resistivity of 2.0 x 10^(-6) Ohm.m. The diameter of wire C is 1.00 mm, and the diameter of smaller wire D is 2/3 times the diameter of wire C. The wires are joined as shown in the figure, and a current of 2.0 A is set up in them. What is the electric potential difference between points 1 and 3?

Wire C and wire D are made from the same material, having length LC = LD = 1.0 m and the resistivity of 2.0 x 10^(-6) Ohm.m. The diameter of wire C is 1.00 mm, and the diameter of smaller wire D is 2/3 times the diameter of wire C. The wires are joined as shown in the figure, and a current of 2.0 A is set up in them. What is the electric potential difference between points 1 and 3?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The inner conductor of a coaxial cable has a diameter of 0.5 mm, an outer conductor an inner diameter of 6 mm and a length of 50 m. If the inner and outer conductors of the coaxial cable will be joined at one end of the cable, and if the permeability of the insulating material is µ = 4πx10^-7 H/m, what will be the inductance of the cable?
An armature has a resistance of 0.2 Ω at 150°C and the armature Cu loss is to be limited to 600 wattswith a temperature rise of 55°C. If α0 for Cu is 0.0043/°C, what is the maximum current that can bepassed through the armature ?
A 2 AWG Copper conductor is 450' long what is the resistance of the wire? assumed the ambient temp to be 20ﾟC
Define the electrical power in terms of resistance R, current I, and potential difference V.
17- The Electrical resistivity (ρ) of a material is inversely proportional to the length (L) of the material Select one: True False
A piezoelectric actuator is made from a stack of 20 square piezoelectric pads, each 10mm squarewith a thickness of 2mm? Calculate the maximum displacement when 1kV is applied given that d33=100×10-12 C/N, er = 50 and Y = 50GPa.
Distinguish between conductors and semiconductors under the following headings: temperature, coefficient of resistance and band theory.
The collector leakage current in a transistor is 300 μA in CE arrangement. If now the transistor is connected in CB arrangement, what will be the leakage current? Assume β = 120. (2) For a certain transistor, IB = 20 μA; IC = 2 mA and β = 80. Calculate ICBO. (3) In a transistor, IB = 68 μA, IE = 30 mA and β = 440. Determine α rating of the transistor. Then determine the value of IC using both the α rating and β rating of the transistor.
The accepted resistivity value at room temperature for copper wire is 1.7421 x 10-8 ohm meter. please explain why or why not the measurements recorded are within some percent error of thius value. calculate resistivity and show the percent error. Use R=p L/A Using the formula calculate p
Calculate the Resistance, if the RTD temperature is 321.9 °C and Sensitivity is 3 °C/ohm?
A certain toaster has a heating element made of Nichrome resistance wire. When the toaster is first connected to a 120 V source of potential difference (and the wire is at a temperature of 20.0°C), the initial current is 1.90 A, but the current begins to decrease as the resistive element warms up. When the toaster reaches its final operating temperature, the current has dropped to 1.5 A. (d) Determine the operating temperature of the heating element.
Calculate voltage drop across a capacitor by integrating Eq. (3.4)