Answered: Example 3.2 An undetermined number of…

Example 3.2 An undetermined number of feet of wire have been used from the carton of Fig. 3.6. Find the length of the remaining copper wire if it has a diameter of 1/16 in. and a resistance of 0.5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2. The 40mm diameter steel rod AB shown in Figure 2 is resting on frictionless rollers between two…

Q: steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter . The internal diameter of…

Q: A bar of circular cross section is to suspend a tank of water 4 ft. below a ceiling. The tank can be…

Q: An object weighing 51kg is suspended from two ropes that are attached to the ceiling 1.5m apart. The…

Q: 8. Concrete sidewalks are always laid in sections, with gaps between each section. For example, the…

Q: A 115 m long steel cable with a cross-sectional area of 1.13 x 104 m² is subjected to a tensile…

A: Given , Length of the cable , L =115 m Cross sectional area , A = 1.13*10-4 m2. Force acting , P…

Q: A horizontal bar is supported by two suspended vertical wires 240 mm apart fixed to a rigid support.…

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

Q: Calculate the change in length of a 1000-m-long stainless steel cable when itstemperature changes by…

A: given: Length of the stainless steel L=1000mtemperature change ∆T=1000C

Q: A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given Tensile modulus, E1 = 10 GPa E2 = 0.4 GPa Find Tensile…

Q: A power transmission cable consists of eighteen copper wires each of 2 mm diameter surrounding four…

Q: A wire of diameter 3 mm and length 4 m extends by 2.5 mm when a force of 10 N is applied. Find…

A: Given, Diameter of the wire = d = 3 mm Original length of the wire = L = 4 m = 4000 mm Change in…

Q: A steel cable with nominal diameter 25 mm as shown in Table Q2(a) is used in a construction yard to…

Q: A rectangular plate, 30mm by 60 mm is subjected to a tensile force of 5kN in the direction of the…

A: GIVEN DATA- w=30mm d=60mm Diameter D=15mm Load F=5KN Maximum stress =80 N/mm2 Stress concentration…

Q: A pressure tank 5 m long and a mean diameter of 1 m is to be fabricated from a 10mm thick sheet. A 5…

Q: thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of the hoop formed by…

Q: Two bolts A and B of same material and length are subjected to identical tensile load. If the…

Q: LA = 2600 mm2 1000 mm E = modulus of elasticity = 200 GPa a = coefficient of thermal expansion

A: Thermal stress is generated inside the rod because of the change in the temperature or temperature…

Q: A steel band 6mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

A: Answer: (a) The necessary increase in temperature is 52.32℃. (b) The stress occurred in the hoop is…

Q: A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the…

A: The free body diagram of the ladder is as follows:

Q: band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The interval diameter of the hoop…

Q: Consisting of chrome-nickel and bronze, the largest horizontal P force it can carry, and…

Q: A pin fin installed to a wall is replaced by the same material and diameter but with larger length.…

A: Solution:

Q: A steel rod, circular in cross section, tapers from 2.5 cm diameter to 1.25 cm diameter in a length…

Q: Two masses of 220 lbs are suspended by wires that are 0.2 inch in diameter. One wire is of aluminum…

Q: A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the…

A: Given Length of the ladder = 10 m Weight of the ladder = 350 N Ladder angle = 30o Weight of the…

Q: Q2/ A compound cylinder is formed by shrinking a tube of 250 mm internal diameter and 25 mm wall…

Q: A storage vat full of oil is in the form of a frustum of a cone 2m diameter at the top 4m diameter…

Q: Two vertical wires are suspended at a distance of 500 mm apart as shown in Fig. 4.18. Their upper…

Q: m high and 5 m in diameter is to be filled with water. Find the minimum thickness of the tank…

Q: A force of 25,000 N will cause 1cm x 1cm bar of carbon steel to stretch from 20 cm to 20.040 cm.…

Q: The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel…

A: In the given problem, there is a steel boat. So, it must float over water. To float above water, the…

Q: Find the horizontal force necessary at the base to keep the ladder from slipping. Draw a FBD

Q: A copper rod 6cm in diameter is placed within a steel tube, 8cm external diameter and 6cm internal…

A: Given Data The diameter of the solid copper bar is: Dcu=6 cm=60 mm The external diameter of the…

Q: Two threaded bolts A and B of same material and length are subjected to identical tensile load If…

A: Given:Equal tensile load,P1=P2=P,L=L1=L2dA=12 mmUA=strain energy in bolt A,UB=strain energy in bolt…

Q: shows two tubes, one of copper and another of steel of equal length and rigidly connected at their…

A: Given that, Internal diameter of copper tube, dc=100 mm,External diameter of copper tube, Dc=125…

Q: It is located on the ground with a safety stress of 50 kg/cm^2. a) Find the biggest P value that can…

A: Safety Stress =50 kg/cm2 Surface area of upper slab A= 20cm×20cm= 400cm2 Surface area of lower block…

Q: A thin spherical pressure vessel of 200 mm diameter and 1 mm thickness is subjected to an internal…

Q: The 40mm diameter steel rod AB shown in Figure 2 is resting on frictionless rollers between two…

Q: A 129 ft tower is located on the side of a mountain that is inclined 19* to the horizontal. A guy…

Q: Question 2 The uniformly distributed force f (unit: N/m) is applied along the axis of the bar, and a…

Q: Calculate the change in 5 m long copper wire when its temperature changes by 60° C. State your…

A: Given, length of the copper wire=5m Change in temperature, ∆T=60°C From the mechanical properties of…

Q: A uniform tubular pipe 100ft long and weighing 55lbs is supported by a fulcrum as shown in the…

Q: A lead cylinder is placed into a blind hole cut into a large tungsten block, Assume it is a tight…

A: given data pressure applied at the top= 50MPa cylinder length L= 100mm dia of cylinder = 25 mm

Q: Calculate the axial stress in a tube that is stretched by a tensile axial force of 4500 N if the…

A: Write the given data. F=4500 Ndo=25 mm=0.025 mdi=20 mm=0.020 m

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

DONE
Example 3.2 An undetermined number of feet of wire have been used
from the carton of Fig. 3.6. Find the length of the remaining copper
wire if it has a diameter of 1/16 in. and a resistance of 0.5.
FIG. 3.6 Example 3.2.
Get this answer with Chegg Study
SEE THE ANSWER

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two cylinders, 0.75 m in diameter (upper cylinder is 1.5 m long, k = 0.5 W/m-K; lower cylinder is 1.1 m long, k = 1.3 W/m-K) are inside a frustum of a square pyramid (k = 0.053 W/m-K) as shown in the diagram. The upper face is at 250 oC and the lower base is at 100 oC. Calculate the resistance in C (in K/W).
Compute the relative change in resistance, ΔR/R, if a piezoresistive device experiences stress of 20 MPa in one direction. Use a value of 3.84 GPa for Young's modulus of the piezoresistive material. Express your answer in three decimal places.
A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter . The internal diameter of the hoop formed by the band is 29.98cm . By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder ? What stress will occur in the hoop when it reaches the same temperature as the cylinder , if the deformation of the cylinder may be neglected ? (Write complete solution)
Two cylinders, 0.75 m in diameter (upper cylinder is 1.5 m long, k = 0.5 W/m-K; lower cylinder is 1.1 m long, k = 1.3 W/m-K) are inside a frustum of a square pyramid (k = 0.053 W/m-K) as shown in the diagram. The upper face is at 250 oC and the lower base is at 100 oC. Calculate the resistance in A (in K/W).
A horizontal bar is supported by two suspended vertical wires 240 mm apart fixed to a rigid support. A load W is attached to the bar. The left – hand side wire is of copper with a diameter of 5 mm and the right – hand side wire is of steel 3 mm in diameter. The length of both wires is 4 m initially. Neglect the weight of the bar and take ES = 210 GPa and EC = 120 GPa. 24. Find the position of the weight on the bar relative to the copper wire so that both the wires extend by the same amount. Calculate the stress in the steel wire if W = 1 kN. Calculate the stress in the copper wire if W = 1 kN.
What is the required insulation for a 270 ft long pipe with inner radius 3.55 inches. Foam will be used with K value 0.02. Outside temperature is 135 degrees F. Please show calculations.
A steel bar 300 mm long, 50 mm wide and 40 mm thick is subjected to a pull of 300 kN in the direction of length. Determine the change in volume. Take E = 2x105 N/mm2and μ= 0.25.
The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel (ρsteel=7900kg/m3)(ρsteel=7900kg/m3). The sides are made of 0.550 cmcm -thick steel. To do this problem, assume that the bottom of the boat is the full dimensions, but that the sides of the boat are welded onto the top of the bottom (so the total side height is the height of the side plus the thickness of the bottom). Find the h ( cm)
A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The interval diameter of the hoop formed by the band is 29.98cm. By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder? What stress will occur in the hoop when it reaches the same Temperature as the cylinder, if the deformation of the cylinder may be neglected?
A square bar subjected to a tensile load of 100kN having a gauge length of 200mm extends to a length of 0.19mm . Given the tensile strength as 200 MPa , determine ( 1 ) Side of the bar ( express in mm ) Final length ( express in mm ) Modulus of elasticity ( express )
The error in a measurement due to strain when using a tape measure depends on the material that it is made of. For a tape with a cross section of 10 mm by 0.7 mm, calculate how much error is introduced in inches into the measurement at a 300 ft length if the tape is pulled with 80 N and if the tape is made of: a) mild steel (E = 30 x 10^6 psi), b) polycrystalline aluminum (E = 10 x 10^6 psi) c) fiberglass composite (E = 3.5 x 10^6 psi in the long direction)
The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the tube of length L = 10.3 in. Find the maximum safe load P (in lb with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.98 sq, in. area of aluminum = 3.17 sq, in. E of copper = 17066931 ksi E of aluminum = 10016839 ksi allowable stress for copper = 19002 ksi allowable stress for aluminum = 10966 ksi