The lap joint is fastened with four ¾-inch diameter rivets. Ø a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. Ø b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. Ø c. what is the maximum value of the load P (kips) that can be applied to the joint?

The lap joint is fastened with four ¾-inch diameter rivets. Ø a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. Ø b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. Ø c. what is the maximum value of the load P (kips) that can be applied to the joint?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
The lap joint is fastened with four ¾-inch diameter rivets. ➢ a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➢ b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➢ c. what is the maximum value of the load P (kips) that can be applied to the joint?
The lap joint is fastened with four ¾-inch diameter rivets. a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. c. what is the maximum value of the load P (kips) that can be applied to the joint?
The lap joint shown is fasted by 20mm diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 96MPa and the bearing stress is limited to 124 MPa. Assume the Applied load is uniformly distributed among the four rivets.
A flexible cable and rigid boom system is used to lift a load of 65kN at the end of Boom at point C. Points A and B are considered pinned in nature. The allowable shearing stress at all bolts are 250MPa and the allowable bearing stress at all bolts are 300MPa. Note that the initial position of boom is horizontal and segment A and B are vertical. Determine the horizontal reaction at A. 3. Determine the vertical reaction at A.
The lap point is fastened with four 20-mm-diameter rivets. the working stresses are 110 MPa for rivets in shear and 180 MPa for plates in bearing. Find the maximum safe load P that can be applied to the joint. Assume that the load is equally distributed among the rivets
The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be applied if the working stress are 14000 psi for shear in the rivet and 18000 psi for bearing in the plate. Assume that the applied load is distributed evenly in the 4 rivets. The plate is 7/8 in. thick and 4 in wide.
The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below. Pins at A, C, and D are smooth. Determine (a)The load P.(b)The minimum diameter for pin C if it is in single shear and the cross-shearing stress is limited to 70 MPa.(c)The minimum diameter for pin D if it is in double shear and the cross-shearing stress is limited to 70 MPa.
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the B diameter of pin?
Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
The lap joint is fastened with four 3/4-in. diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.
In the clevis shown in the figure, determine the minimum bolt diameter and minimum thickness of each yoke that will support a load P = 55kN without exceeding a shearing stress of 70 MPa and a bearing stress of 140 MPa