The lap joint shown is fastened by four 4-in.-diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 14 ksi and the bearing stress in the plates is limited to 18 ksi. Assume the applied load is uniformly distributed among the four rivets. P P 4 in 7/8 in 7/8 in P P

The lap joint shown is fastened by four 4-in.-diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 14 ksi and the bearing stress in the plates is limited to 18 ksi. Assume the applied load is uniformly distributed among the four rivets. P P 4 in 7/8 in 7/8 in P P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
From the given bracket shown, which consist of two plates riveted to the column by 4-22mm Ø rivets which is subjected to an eccentric load of 150 kN. 1. Which of the following gives the shearing stress due to axial load only? a. 49.325 MPa b. 70.25 MPa c. 80.47 MPa d. 68.25 MPa 2.. Which of the following gives the shearing stress due to moment alone? a. 69.76 MPa b. 70.94 MPa c. 56.39 MPa d. 64.32 MPa 3. Which of the following gives the maximum shearing stress? a. 110.30 MPa b. 120.40 MPa c. 140.50 MPa d. 105.70 MPa
The lap joint is fastened by 20 mm rivets placed alongside each other as shown along the length of the plate. Determine the safety of the lap joint to carry an axial load P=180 KN if the shearing stress in the rivets is limited to 60 MPa, the bearing stress in the plates to 110 MPa, and the average tensile stress in the plate is limited to 140 MPa. Plate width, W=140 mm, splice plate thickness, t=15 mm and main plate thickness, t = 40 mm. P = 180 KN
The five-bolt connection must support an applied load of P = 3500 lb. If the average shear stress in the bolts must be limited to 29 ksi, determine the minimum bolt diameter that may be used for this connection.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 30mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120MPa and it's angle of twist is limited to 7deg. Use G=83GPa for steel. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.
The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α = o0 : (a) The normal stress in the bar EC of uniform cross-sectional area 15 x 10-5 m2 . (b) The shearing stresses in the 10 mm diameter pins at D and E if both are in double shear.
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below. Pins at A, C, and D are smooth. Determine (a)The load P.(b)The minimum diameter for pin C if it is in single shear and the cross-shearing stress is limited to 70 MPa.(c)The minimum diameter for pin D if it is in double shear and the cross-shearing stress is limited to 70 MPa.
(D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is required, determine the allowable shear stress in this pin. in ksi (E) The pin used at B is a double shear pin connection. Determine the minimum pin cross-sectional area, and the corresponding minimum pin diameter that can be used at B. (Amin IN in.2 and dpin IN in.) (F) Determine the deformations in rods (1), (2), and (3) when load P equals Pmax from Letter C. ANSWERS in inch (G) Using the results from Letter F, determine the deflections of Joint B and Point D. ANSWERS in inch
A flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the flange thickness if the bearing stress on the flange is 95 MPa. A. 10 mm B. 20 mm C. 25 mm D. 30 mm
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
A load P is supported by two concentric steel springs.Given:Inner Spring:30 turns of 20-mm ø wireMean ø = 150 mmOuter Spring:20 turns of 30-mm ø wireMean ø = 200 mmFind the maximum load that will not exceed a shearing stress of 140 MPa in eitherspring. G = 83 GPa.