The largest soft aluminum tubing that may bent by hand is ________________ -inch outside diameter. *

Q: Which cutting tool material has the highest hardness?   a. Carbide b. Tool steel c. CBN d. HSS

A:

Q: Minimum thickness?

A: Given; A building has to be maintained at, TI=210 C (DB)Wet bulb, Tdb=10.170COutside temperature,…

Q: pitch, the torque required for achieving the tightening force is

A: Given data; tightening force=2200 N Pitch=0.004 m

Q: (4) The average flow stress is the flow stress multiplied by which of the following factors: (a) n,…

A: “Since you have asked multiple question , we will solve the first three questions for you. If you…

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: stiffness of the shaft, the general measures are

A: Solution.  The stiffness can be increased by. Replace carbon steel with alloy steel Surface…

Q: What is the discontinuity of loading?

A: The load along the length of the structure, say a beam if is consistent then we can say that the…

Q: What is impact loading?

A: Impact loading is a type of loading whose period of action is very less. Generally, when the time of…

Q: What is a double-rod cylinder? When would it normally be used?

A: Two types of cylinders are: Single rod cylinder Double rod cylinder.

Q: Due to imperfections in manufacturing or specific applicationof the load, a column will never…

A: Under the application of axial load over a column when there is a deflection in the lateral…

Q: 8) Which of the following formula generally - used for low carbon steel? OElectrode tip diameter =…

A: When the electrode tip is too small , the nuggets will be form too small and weak , and when it is…

Q: What are non conservative force?

A: Non conservative forces are those forces ,which if act, there is loss of mechanical energy of a…

Q: Describe the importance of pigging, bearing and shaft seals.

A: Pigging is defined as the process of pipeline review or maintenance in which various inspection…

Q: The radial distance between the addendum circle of a gear and the dedendum circle of a gear is known…

A: option 4 is correct -Total depth   Total depth:- This is the height of a tooth. It is the radial…

Q: 11. Orientation of two circles with the same center. _ 12. Press fitting a pin/ shaft to a hole…

A: 11) Orientation of two circles with same center.  Answer: Concentric Circles   12) Press fitting a…

Q: a). Briefly explain any one type of metal bending operations with a neat diagram. b). Write the…

A: Metal bending and its application

Q: Main characteristic when cutting Steel ISO P is: a) Machining at higher speeds creates abrasive…

A: The metalworking process is classified by ISO in six categories such as P, M, K, N, S, and H. Each…

Q: By what means kind of small area or stripe be selectively hardened and a large steel pa

A: induction hardening and flame hardening

Q: Which one of the given options is Wrong?         a)Tool life usually measured in days       b)Strain…

A: Tool life is generally measured in minutes  Strain hardening occurs when a material undergoes large…

Q: Where is a bent material most likely to fail?

A: Let us take an example. Consider any beam applied with external bending  moment . This beam…

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: Which of the following formula generally used for low carbon steel?

A:

Q: sketch write short notes on any two types of rolling bearings

A:

Q: splacements and reaction

A:

Q: What happens when an external torque is applied to a shaft?

A:

Q: Define the following terms: Sagging, Hogging, Point of Contraflexure?

A:

Q: What is meant by the term " Fractured conrod"?

A: Fracture conrod means fracture connecting rod. This is a technology used in some of the latest…

Q: Describe the operational characteristics of a Direct Acting Relief Valve B) A single paragraph…

A: The characteristics of a direct-acting relief valve can be used in a simple circuit to control the…

Q: What is the typical C content of the following mild steel tools? Nails/Spykers =…

A: The typical carbon content in the Nails or spykers.................. ........

Q: Give me answer  both c and d. I don't want single answer. Thank you  (c) Provide the reasons for…

A: The reasons behind ensuring tension member slenderness can't more than 300  because while designing…

Q: Advantages and disadvantages of using smaller bolts than bigger bolts

A:

Q: What is the mechanical advantage of a 1/4" diameter screw with 20 threads per inch?

A: Calculating the mechanical advantage of a 1/4" diameter screw with 20 threads per inch.

Q: What’s the difference between radial arm and upright drill press?     a)Different cutting tool…

A: Given data : radial arm upright drill press

Q: Describe and sketch open drill jigs with its components

A: Open type jig , in which the top plate is arrange to swing about a fulcrum point , so that it is…

Q: What percentage of strength of a solid circular steel shaft of 160 mm diameter is lost by boring 100…

A: Given data as per question Diameter of solid shaft =160 mm Axial hole diameter =100 mm

Q: What firce is requure to punch off 5 mm hole out of a 4 mm thick plate if the ultimate punching…

A: Ultimate Punching Stress (Su) = 200 MPa The actual shear stress in the material is τ=F/A; Thus the…

Q: Define the term Angle of Twist?

A: Whenever a twisting moment is applied on the shaft, the shaft's cross-section tends to rotate or…

Q: Define Iron Stirrups

A: Given Stirrups To find Iron stirrups

Q: Describe the different types of hammers.

A: Types of hammer: Claw hammer: This is the most common hammer for general work available with…

Q: The strains can be eliminated by using the generalized form of Hooke’slaw.True or false?

A: False, strains cannot be eliminated from the generalized hooke's law

Q: Why is it better to have hollow bars if they are being twisted?

A: If hollow and solid bar have the same radius then solid bar would resist slightly more torque. in…

Q: What are steel sections?

A: Steel sections are the bread and butter of steel fabrication. The planners, architects and engineers…

Q: Which type of bands are used for cutting many types of steel?     a)Alternate set b)The standard…

A: Hook tooth blades are able to take deep bits out of the material. They are used mostly for hardwood…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.