The leaning Tower of Pisa is 59.1 m high and 7.44 m in diameter. The top of the tower is displaced 4.01 m from the vertical.Treat the tower as a uniform, circular cylinder. (a) What additional displacement, measured at the top, would bring the tower to the verge of toppling? (b) What angle would the tower then make with the vertical?

The leaning Tower of Pisa is 59.1 m high and 7.44 m in diameter. The top of the tower is displaced 4.01 m from the vertical.Treat the tower as a uniform, circular cylinder. (a) What additional displacement, measured at the top, would bring the tower to the verge of toppling? (b) What angle would the tower then make with the vertical?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 31PQ: A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm...

See similar textbooks

Similar questions

A spade is modelled as a uniform rod, of mass 2kg and length 90cm, attached to a uniform square lamina, of side 20cm and mass 0.5kg. A gardener holds the spade horizontally with hands 30cm and 60cm from the end of the rod. Find the vertical forces exerted by the gardener's hands. Im stuck on this q, pls help.
overhead view of a rigid rod that turnsabout a vertical axle until the identical rubber stoppers A and B are forced against rigid walls at distances rA = 7.0 cm and rB = 4.0 cmfrom the axle. Initially the stoppers touch the walls without beingcompressed.Then force of magnitude 220 N is applied perpendicularto the rod at a distance R = 5.0 cm from the axle.Find the magnitudeof the force compressing (a) stopper Aand (b) stopper B.
A uniform horizontal beam 5.00 m long and weighting 3.03 102 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 53.0° with the horizontal (Figure (a)). If a person weighing 6.05 102 N stands 1.60 m from the wall, find the magnitude of the tension in the cable and the force exerted by the wall on the beam. T = N Rx = N Ry = N Even if we selected some other axis for the torque equation, the solution would be the same. For example, if the axis were to pass through the center of gravity of the beam, the torque equation would involve both T and Ry. Together with Equations (1) and (2), however, the unknowns could still be found—a good exercise. In this example, notice the steps of the Problem-Solving Strategy could be carried out in the explicit recommended order.QUESTION What happens to the tension in the cable if the man in Figure (a) moves farther away from the wall? The tension would…
a uniform beam with a weight of 60 N and a length of 3.2 m is hinged at its lower end, and a horizontal force of magnitude 50 N acts at its upper end.The beam is held vertical by a cable that makes angle u = 25° with the ground and is attached to the beam at height h = 2.0 m. What are (a) the tension in the cable and (b) the force on the beam from the hinge in unit-vector notation?
Resting horizontally, a wheelbarrow has a total mass of 65 kg, with its center of gravity 12 cm from the wheel axle.A person grips the handles 1.3 m from the axle. What total vertical force must the person exert to lift it?
a uniform beam of length 12.0 m is supported by a horizontal cable and a hinge at angle u =50.0°. The tension in the cable is 400 N. In unit-vector notation, what are (a) the gravitational force on the beam and (b) the force on the beam from the hinge?
A uniform horizontal beam 10.0 m long and a mass of 82 kg is attached to support cables on either end. The cable on the left end makes an angle of 120 with x-axis and the cable on the right end makes an angle of 30̊ with the x-axis. If a person of mass 82 kg stands 7 m from the right end, find (a) the magnitude of the tensions TL and TR in the cables.
Find the knee joint angle in degrees given the following coordinates: Joint x (m) y (m) Hip 0.86 0.87 Knee 0.92 0.54 Ankle 0.60 0.41
A uniform beam of length L = 2.2 m and mass M = 33 kg has its lower end fixed to pivot at a point P on the floor, making an angle θ = 15° as shown in the digram. A horizontal cable is attached at its upper end B to a point A on a wall. A box of the same mass M as the beam is suspended from a rope that is attached to the beam one-fourth L from its upper end.What is the y-component Py of the force, in newtons, exerted by the pivot on the beam? Py = Write an expression for the tension T in the horizontal cable AB. T = What is the x-component Px of the force, in newtons, exerted by the pivot on the beam? Px =
A uniform ladder is 10 m long and weighs 200 N. , the ladder leans against a vertical, frictionless wall at height h = 8.0 m above the ground. A horizontal force is applied to the ladder at distance d = 2.0 m from its base (measured along the ladder). (a) If force magnitude F = 50 N, what is the force of the ground on the ladder, in unit-vector notation? (b) If F = 150 N, what is the force of the ground on the ladder, also in unit-vector notation? (c) Suppose the coefficient of static friction between the ladder and the ground is 0.38; for what minimum value of the force magnitude F will the base of the ladder just barely start to move toward the wall?
A uniform beam of length L = 11.7 meters and mass of 109.3 kg is pinned at one end and is being supported by a wire as shown. The wire is connected to the beam x = 3.3 meters from the pin. A person of mass 81.6 kg is standing all the way out on the edge of the beam. If θ = 17.3 degrees and φ = 79.4 degrees, what is the tension in the wire?
A uniform horizontal beam 5.00 m long and weighting 3.03 102 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 53.0° with the horizontal (Figure (a)). If a person weighing 6.05 102 N stands 1.60 m from the wall, find the magnitude of the tension in the cable and the force exerted by the wall on the beam. T = N Rx = N Ry = N