Considercylin dsical nickel wireofa4.0 mm in diamelor andlong.A the Ni wire is207 x6N/m² (207X 10°N/mm?), when e200 mmThe elatic modulsLoadofthe deformation isa) Calculat the tonsik stmin and the elongitinf the wire (düphemeit/defomition alorgtaik direiton)여 니00 N lsapplied. Assume thatto tallyelastic .disthetensileGiven that the wire's naben ispoisson's0.3, caleulate the batral stain and change(the wire shoulddisection.)to-the widththe wireof-the later alShorink9 Aften reloning the load, whitthe longth and widthhapprsofthe wire Y

we have to calculate stress strain elongation , lateral strain.

Answered: the load, what happorns Afler releasing…

Engineering

Mechanical Engineering

the load, what happorns Afler releasing the longth and width ok the wire

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wire in the wire drawing machine, at the entrance entranceIt will be drawn from a drawer with 15 ̊. of the wireinlet diameter (D0) 2.5 mm and outlet diameter (Df) 2.0 mmdirection. Die and wire surface transitionswindow (μ) is 0.07. Wire strength (K)It is 205 MPa and the strain hardening superposition (n) is 0.20.Pre-section of wire (A0) 4.91 mm2and sector section area (Af) 3.14 mm2direction.Accordingly, wire drawing is done;a) Regression,b) Calculate the pulling force
1. A steel pipe of length 4 ft, outside diameter of 6.0 in., andinside diameter of 4.5 in., is compressed by an axial forceof 140 kips. The material has a modulus of elasticity of30,000 ksi and Poisson’s ratio of 0.30. Determine thefollowing quantities for the pipe:a. The shortening.b. The lateral strain.c. The percentage increase in the outer and theincrease in the inner diameter.d. The percentage increase in the wall thickness.
A polycrystalline metal has a plastic stress--strain curve that obeys Hollomon’s equation,σ = K εnDetermine n, knowing that the flow stresses of this material at 2% and 10%plastic deformation (offset) are equal to 175 and 185 MPa, respectively.
1. Most bridges contain interlocking steel grates (α steel = 1.2 x 10 - 5 ºC -1 ) that allow the bridge toexpand and contract with the changes in temperature. The Golden Gate Bridge in San Francisco isabout 1350 meters long.(A) The seasonal temperature variation in San Francisco ranges from about 0ºC to 30ºC. Howmuch will the bridge expand between these two extremes?(B) What percent of the length of a subcompact automobile, 2.5 meters, does this gaprepresent?2. Selena has a fire in her fireplace to warm her 20ºC apartment. She realizes that she hasaccidentally left the iron poker (α iron = 1.2 x 10 -5 ºC -1 ) in the fire. How hot is the fire if the 0.60-meter poker lengthens 0.30 cm?3. Just before midnight, when the air temperature of 10.0ºC, Karl stops and fills the 0.0600 m 3 gastank in his car. At noon the next day, when the temperature has risen to 32ºC, Karl finds a puddle ofgasoline (βgas = 3 x 10 -4 ºC -1 ) beneath his car.(A) How much gasoline spilled out of Karl's car?…
A hydraulic cylinder cylinder that pushes a heavy tool during the outward stroke, placing a compressive load in the piston rod as shown below. If the material for the piston is SAE 4130 WQT 1300 Steel, and stress concentration factor is 1.0 for this design problem. If also it is given that the estimated actual endurance limit in this application sn ' = 22.3 ksi, and the fluctuating stress on the piston as: σm = 2.9 ksi, and σa = 4.1 ksi, please calculate the design factor based on the Goodman Criterion only: N = ___ . Please take the material property from the textbook, and you could just use your answer(s) from the problems above. Calculate your answer to 1 digit place.
A pressure difference of 35 pa is available to force -10c air. through a circular sheet metalduct 400 mm in diameter and 20m long. Find thevelocity in m/s. A.11.64 B.38.20 C.12.81 D.20.60 SHOW DETAILED SOLUTIONS
The diameter (d) of a solid rod (i.e., with a circular cross-section) is 16 mm and ismade from a homogeneous material. The length (L) of the rod is 1.75 m andYoung’s Modulus for the material (E) is 250 GPa. When the rod is placed undertension it experiences deformation and a stress (?) of 650 MPa. Calculate thefollowing:(i) Strain energy (U) to 2 decimal places in Joules.(ii) Strain energy per unit volume (U/V) in J/m3.(iii) The change in length ∆L to 2 decimal places in mm.(iv) The strain (?) due to deformation to 2 significant figures
How is parabolic shear-stress distribution and Linear normal stress distribution created?
A round shaft, made of cold-finished AISI 1020 steel, is subjected to a variable torque whose maximum value is 7238 cm-kg. For N  5 on the Soderberg criterion, determine the diameter if (a) the torque is reversed, (b) the torque varies from zero to a maximum, (c) the torque varies from 3141 in-lb to maximum.
A 100 × 50 × 25mm steel block is subjected to a hydrostatic pressure of 5 MPa. The Young's modulus and Poisson's ratio of the material are 150GPa nd 0.2 respectively. The change in the volume of the block in mm³ is
EXPLAIN THIS IMAGE https://www.researchgate.net/profile/Carlos-Cuenca-Cabrera/publication/326753159/figure/fig4/AS:659386125008898@1534221311272/Engineering-Stress-Strain-curve-for-both-Brittle-and-Ductile-material-Source.png
A shaft is subjected to an axial pull of ___ and transverse shear force of ___ The yield strength of the shaft materials is ___ and poison’s ratio 0.3. Determine the diameter of shaft using (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory (iv) maximum strain energy theory (v) Maximum total strain energy theory. the Information that you need: Axial pull = 18kN Shear force = 8kN Yield strength = 200MPa