The maximum efficiency of a transformer occurs at 78.3 % of load and the power consumed by the transformer during the short circuit test is 167.9 W, Determine the iron loss of the transformer O A. 13146.57 O B. 131.47 O C. 214.43 O D. 102.94

The maximum efficiency of a transformer occurs at 78.3 % of load and the power consumed by the transformer during the short circuit test is 167.9 W, Determine the iron loss of the transformer O A. 13146.57 O B. 131.47 O C. 214.43 O D. 102.94

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Related questions

Q: A Step-down transformer at Van Eck power station in Windhoek operates at V=10 kV on the primary side…

A: we need to find out the current, on secondary side of the transformer.

Q: 7- The Full load. Cu loss and iron loss of a transformer are 920 W and 430 W respectively. (i)…

A: In this question we need to find loading of the transformer at which maximum efficiency occurs and…

Q: During short-circuit test of a transformer, the core loss of a transformer is negligible. Select…

A: Need to find true false

Q: A transformer with primary winding 1000 turns and primary volatage is 220v, 5OHz and at secondary…

A: The data given in the question are: N1=1000,V1=220V,N2=500,V2=? The secondary voltage can be…

Q: The primary and secondary windings of a 500 kVA transformer have resistances of 0.44 Ω and 0.0027 Ω,…

A: The solution is given below

Q: A distribution transformer has 12 residential customers connected to it. Connected load is 20 kW per…

A: There are 12 residential customers we have given, Connected load=20 kW per house=20×103 W Demand…

Q: A transformer having a transformer ratio of unity is called a/an: O a) isolation transformer. O b)…

A: Option a) isolation transformer

Q: A transformer has 595 primary turns connected to a 1.5 kV / 205 V supply, then the number of…

A: Primary turns = 595 voltage ratio = 1500 V205 V For transformers:…

Q: 4.5 +J6 ohms referred to the high-Voltag A 1200/240-V practical transformer has an equivalent…

Q: As given in the figure, the primary side of an ideal transformer is fed from a 400 Volt source with…

Q: Find the efficiency of a 150 kVA transformer at 25 % full load at 0.8 p.f. lag if the copper loss at…

Q: A 15.5-kVA, 2200/210-V transformer has circuit parameters referred to the primary side given in…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: 23/A) A 1000-VA 230/115-V transformer has been tested to determine its equivalent reunt. The results…

Q: From the short circuit test and open circuit test in #19 and #20, the equivalent circuit of a…

Q: Q1// What is the purpose of conducting experiments (o.c) and (s.c) on asingl- nhase transformer?

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: A pure transformer is used to form a step-up autotransformer with common winding of 7200 V and 1400…

Q: A 1000-VA 380 / 110 V conventional transformer is to be used to supply power from a 490-V source to…

A: From the given data of normal transformer, KVA=1000 VAVP=380 VVS=110 V To the Auto-transformer…

Q: The Full load. Cu loss and iron loss of a transformer are 920 W and 430 W respectively. (i)…

Q: The maximum efficiency of a transformer occurs when the constant core loss equal the variable copper…

A: The solution is given below

Q: A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and…

Q: A 500 kVA transformer has an efficiency of 95% at full load and also at 60% of full load; both at…

A: (a)Separation of losses: Where Pi is iron loss and PC is full load cu loss.…

Q: An ideal transformer is connected to a voltage source given by es(t) = 100cos(2000nt)V on the…

A: In this question, Ideal transformer is connected to the es = 100cos(2000πt) V. Transformer turn…

Q: In an ideal transformer, the power in the secondary coil is 10 kW. The voltage of the primary is 500…

A: The given information for an ideal transformer is Power in secondary coil P2=10 kW. Voltage of…

Q: DHA) a) Draw an equivalent circuit of a current transformer and derive expressions for ratio and…

A: a) Current transformers- These are those type of transformers, which are mainly used for measurement…

Q: 11. A 440/110 V transformer has a primary resistance of 0.03 ohm and secondary resistance of 0.02…

Q: To a distribution transformer 8 residential consumers are connected. Each house connected load is 10…

A: Since in the given question, there is no mention of the demands or average demand or load factor, we…

Q: A 200-KVA transformer has an efficiency of 98 % at full-load. If the maximum efficiency occurs at…

Q: A 15-kVA 8000/230-V distribution transformer has an impedance referred to the prima of 80+ j3000.…

A: a. The turns ratio of the transformer is determined as a=8000230=34.78 The load impedance referred…

Q: A small plant produces electric energy and, through a transformer, sends it out over the…

A: Given that I = 50 AV = 20 kV. R = 1.2 ohms/km L= 25 kmRline=1.2×25=30 ohm (a) Power loss in the…

Q: 2. Sketch a simplified equivalent circuit of a transformer

A: Electrical machines can be either generator, transformer or motors. They can be either Ac machines…

Q: A transformer has 500 primary turns and 3000 secondary turns. If the primary voltage is 240V, the…

A: Find explanation below

Q: A Step-Down Transformer. A transformer connected to a 120 V (rms) ac line is to supply 12.0 V (rms)…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: A transformer rated at 1000 kVA is operating near capacity as it supplies a load that draws 900 kVA…

A: According to the question, we have to find, real power delivered to the load and how mu ch…

Q: The short circuit losses of a 15 kV single-phase transformer are 700W. Given that the reduced…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: Determine the regulation of a transformer in which the percentage resistance drop is 1% and the…

Q: As given in the figure, an ideal transformer with a 2: 1 winding ratio is fed from a 240 Volt source…

Q: 3. A 500/250 V, 1-phase transformer has constant losses of 150 W. When delivering an output of 8 kW…

A: In this question we need to find a variable loss of the transformer for given loading conditions. In…

Q: A 200 – kVA transformer with impedance of 5 percent and the power factor of the load is 85 percent.…

A: Given, A transformer with KVA rating, S=200 kVA Impedance, Z=5% Power factor, cosϕ=85%=0.85 Primary…

Q: Q.29: For the ideal transformer circuit shown, find the 452 average power delivered to (1Q)…

A: for the ideal transformer circuit shown find the average power delivered to 1ohm resistor

Q: A Buck converter has an output power of 1950 Watts, and a source voltage of 1000V (the constant DC…

A: For a buck converter Vo=DVs.

Q: What is the level of the peak voltage at the secondary 1 (Vsecondary 1) and secondary 2 (Vsecondary…

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

A: In this question, We need to impedance of the approximately in the primary side and draw the…

Q: All data given were taken from the primary side of the transformer. (a) Find the equivalent circuit…

A: Given Data:

Q: Asiacell|ASIACELL 3G 2G zain IQ BartlebySolutions.. 1 • Q1: During the separation of transformer…

A: Note :- as per our guidelines we are supposed to answer 1 question at a time in case of multiple…

Q: A 1000-VA, 230/115-V transformer has been tested to determine its equivalent cir- cuit. The results…

A: Transformer of 1000 VA,230/115-v Open circuit test(secondary side)Voc=115 vIoc=0.11 APoc=3.9 wShort…

Q: 302 j722 םרהj 302 The label values of the single-phase transformer whose electrical equivalent…

A: Given: A 20 KVA, 15400 V/240 V, 50 Hz, single-phase transformer has the following equivalent…

Q: F ← N₂ = 40 t ell Denotes iron-core 1,-100 mA For the iron-core transformer of figure. Find the…

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

The maximum efficiency of a transformer occurs at 78.3 % of load and the power consumed by the transformer during the short
circuit test is 167.9 W, Determine the iron loss of the transformer
O A. 13146.57
O B. 131.47
OC. 214.43
O D. 102.94

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
An ideal transformer has no real or reactive power loss. (a) True (b) False
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit equivalent circuit shown in part (c) contains an ideal transformer which cannot be accommodated by some computer programs. (a) True (b) False (ii) In the - circuit representation for real c in part (d), the admittance parameters Y11 and Y12 would be unequal. (a) True (b) False (iii) For complex c, can the admittance parameters be synthesized with a passive RLC circuit? (a) Yes (b) No
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.