Q3.The momentum equation for an inviscid flow with body forces ignored is defined as,a(pu) ¸ a(puu) , d(puv) _ _ôPây+ốt+Show that for incompressible flow in steady-state this simplifies as given below;диди+ pv-ƏPpu-

Answered: Image /qna-images/answer/22d26005-6cf2-468b-9491-03c65b4a1308.jpg

Answered: The momentum equation for an inviscid…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider steady flow of water through an axisymmetric garden hose nozzle. The axial component of velocity increases linearly from uz, entrance to uz, exit as sketched. Between z = 0 and z = L, the axial velocity component is given by uz = uz,entrance + [(uz,exit − uz,entrance)/L]z. Generate an expression for the radial velocity component ur between z = 0 and z = L. You may ignore frictional effects on the walls.
A fl uid jet of diameter D 1 enters a cascade of movingblades at absolute velocity V 1 and angle β 1 , and it leaves atabsolute velocity V 2 and angle β 2 , as in Fig. P3.78. Theblades move at velocity u . Derive a formula for the powerP delivered to the blades as a function of these parameters.
For a flow in the xy plane, the x component of the velocity is u=3x2y-y3is given. Determine the y component for steady state and incompressible flow. Does this result also apply to unstable, incompressible flow? Why is that? How many possible y components are there? Discuss.
04/13/2021 For this exercise Study and Derive the Bernoulli equation starting with the application of Newton’s second law to a fluid particle.
A sink of strength 20 m2/s is situated 3 m upstream of a source of 40 m²/s in a uniform stream. It is found that, at a point 2.5 m from both source and sink, the local velocity is normal to the line joining the source and sink. Find the velocity at this point and the velocity of the uniform stream. Locate any stagnation points and sketch the flow field.
See the following nozzle, L is 10 cm, Dentrance is 2 cm, Dexit is 0.5 cm. The volume flow rate through the nozzle is 0.227 m3/h. The flow is steady. Estimate the magnitude of the acceleration of a fluid parcel moving down the centerline of the nozzle.
Figure 1) shows a tank of 20∘C water with a nozzle h = 27 cm below the surface. Bernoulli's equation applies to the flow between points 1 and 2 on the streamline, but not to the flow between points 2 and 3.What is the volume flow rate through the nozzle in L/min ? Assume that the water level in the tank is held constant.
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Consider a venturi with a small hole drilled in the side of the throat. Thishole is connected via a tube to a closed reservoir. The purpose of theventuri is to create a vacuum in the reservoir when the venturi is placed inan airstream. (The vacuum is defined as the pressure difference below theoutside ambient pressure.) The venturi has a throat-to-inlet area ratio of0.85. Calculate the maximum vacuum obtainable in the reservoir when theventuri is placed in an airstream of 90 m/s at standard sea level conditions.
Water falls vertically downward from an open faucet with an initial velocity of 66 cm/s. If the stream diameter at the faucet head is 0.5 cm what is the stream diameter at a distance 5 cm below the faucet exit?
In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.
A certain axial flow turbine has an output torque M that isproportional to the volume flow rate Q and also depends onthe density ρ , rotor diameter D , and rotation rate Ω . Howdoes the torque change due to a doubling of ( a ) D and ( b ) Ω ?
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Show that a source flow is a physically possible incompressible floweverywhere except at the origin. Also show that it is irrotationaleverywhere.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS