The motor causes the aluminum shaft containing gears D, E, and F to rotate. The solid shaft has a diameter of 24 mm and a modulus of rigidity of 24 GPa. The bearings at G suddenly jams, after which gear B rotates an additional 0.27 radians and gear C rotates an additional 0.21 radians. Determine the resulting torsion, T, that must be occurring in the shaft between gears D and E. Assume that D and E are rotating the same direction. Also note that gears B and C both have a 60 mmtradius. Express your answer in Nm to the nearest whole Nm.

The motor causes the aluminum shaft containing gears D, E, and F to rotate. The solid shaft has a diameter of 24 mm and a modulus of rigidity of 24 GPa. The bearings at G suddenly jams, after which gear B rotates an additional 0.27 radians and gear C rotates an additional 0.21 radians. Determine the resulting torsion, T, that must be occurring in the shaft between gears D and E. Assume that D and E are rotating the same direction. Also note that gears B and C both have a 60 mmtradius. Express your answer in Nm to the nearest whole Nm.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.2P: Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the...

See similar textbooks

Similar questions

A 37.5-mm-diameter rod 6 mlong elongates 12 mm under a load 236 KN. Thediameter of the rod decreases 0.025 mm during theloading. Determine the following properties of thematerial: (a) Poisson’s ratio.(b) Young’s modulus(c) The modulus of rigidity.
The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF, and a rigid bar G. If the horizontal displacement of end F of rod EF is 0.45 mm, determine thethe magnitude of P.
The aluminum alloy [G = 4000 ksi] pipe is fixed to the wall support at C. The bolt holes in the flange at A were supposed to align with mating holes in the wall support; however, an angular misaligment of 4° was found to exist. To connect the pipe to its supports, a temporary installation torque T'B must be applied to B to align flange A with the mating holes in the wall support. The outside diameter of the pipe is 5.5625 in. and its wall thickness is 0.258 in. The segment lengths are L1= 16 ft and L2 = 24 ft. a) Determine the temportary installation torque T'B that must be applied to B to align the bolt holes at A b) Determine the maximum shear stress τinitial in the pipe after the bolts are connected and the temporary installation torque at B removed c)Determine the magnitude of the maximum shear stress in segment (1) and (2) if an external torque TB= 150 kip-in. is applied at B after the bolts are connected
Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the displacement at end A in (mm). E = 200 GPa
In the system shown, when a compression load P is applied to the rod, what is the bearing stress value in the bearings through which the d diameter pin passes? P = 10kN, pim çapı: d=20mm, bir yatağın kalınlığı: t = 10mm
The rod is pinned at its end A and attached to a torsional spring having a stiffness k, which measures the torque per radian of rotation of the spring. If a force P is always applied perpendicular to the end of the rod, determine the displacement of the force. EI is constant.
The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. If the downward force P will produce a 50 mm vertical displacement at the free end of lever AC, determine the force P if G = 83 GPa.
The torsional assembly consists of solid 1.6 in. diameter aluminum [G = 4,000 ksi] segments (1) and (3) and a central solid 2.0 in. diameter bronze [G = 6,500 ksi] segment (2). Segment lengths are L1 = L3 = 32 in. and L2 = 66 in. Concentrated torques of TB = 2T0 and TC = T0 are applied to the assembly at B and C, respectively. If the rotation angle at joint B must not exceed 3.0°, determine:(a) the maximum magnitude of T0 that may be applied to the assembly.(b) the maximum shear stress magnitude in aluminum segments (1) and (3).(c) the maximum shear stress magnitude in bronze segment (2).
Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the displacement at end A in (mm).
The A-36 steel assembly consists of a tube having an outer radius of 1 inch and a wall thickness of 0.125 inch. Using a rigid plate at B, it is connected to the solid 1-inch diameter shaft AB. Determine the rotation of the tube’s end C if a torque of 200lb inches is applied to the tube at this end. The end A of the shaft is fixed supported.
The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF, and a rigid bar G. If P = 5 kN, determine the horizontal displacement of end F of rod EF.
The two shafts are made of steel (G=11x106 lb/in2). Each has a diameter of 1 in. , and they are supported by bearings at A, B and C, which allow free rotation. If the support at D is fixed, determine the angle of twist of end A when the torques are applied to the assembly as shown. Torque applied at H of 80 ft lbs, and at G of 40 ft lbs in opposing directions as seen in the figure