The open-circuit and short-circuit impedances measured at the input terminals of an air- spaced transmission line 4m long are 2502-50°N and 360220°2, respectively. (a) Determine Z, a, and ß of the line. (b) Determine R, L, G, and C. 0'

The open-circuit and short-circuit impedances measured at the input terminals of an air- spaced transmission line 4m long are 2502-50°N and 360220°2, respectively. (a) Determine Z, a, and ß of the line. (b) Determine R, L, G, and C. 0'

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.33P: Consider a long radial line terminated in its characteristic impedance Zc. Determine the following:...

See similar textbooks

Related questions

Q: A symmetrical, passive, reciprocal and lossless two-port network has a Z, (real) characteristic…

Q: A half-wavelength, lossless transmission line is 1.4 m long and terminated in 20 - j10 0. The…

A: For the lossless transmission line, the characteristics impedance is given as, In the question, the…

Q: 2- Transmission line 10m long has distributed parameters R = 5 Ω /m, L = 6μH/m, G = 10 mS/m, and C =…

Q: A transmission line has a characteristic impedance of 50 ohm and a line resistance of 0.1 ohm/m. If…

A: Since the transmission line is distortion less, the attenuation constant of the line can be…

Q: Line parameters of a transmission line at 2 GHz are R = 10 mn/m, G = 1 µS/m, L = 1 µH/m, C = 1 nF/m…

A: The given circuit diagram is shown below: It is given that: R=10 mΩ/m=10×10-3 Ω/mG=1 μS/m=1×10-6…

Q: A transmission line has the following per-unit-length parameters: L = 0.5 µH/m, C = 200 pF/t R = 4.0…

Q: The open-circuit and short-circuit impedances measured at the input heads of a transmission line…

A: According to the question we have to find the value of Z0,α,β.

Q: Question 1 A telephone line has R µF/km. At a frequency, f propagation constant of the line, and the…

Q: The open-circuit and short-circuit impedances measured at the input heads of a transmission line…

A: Given that zOC=250∠-50°zSC=360∠20° Formula for z is given by z=zOCzSCplugging…

Q: Obtain the input impedance expression Zent for a transmission line terminated in short circuit

Q: A certain transmission line operating at w = 10° rad/s has a = 8 dB/m, B = 1 rad/m, and Z, = 60 +…

A: Given data : ω=106 rad/sα=8 dB/mβ=1 rad/mZ0=60+j40ΩZg=40ΩZL=20+j50Ω

Q: [Q4] An open wire transmission line terminated in characteristic impedance has the following primary…

Q: Transmission line 10m long has distributed parameters R = 5 Q /m, L = 6uH/m, G= 10 mS/m, andC= 25…

A: The value of characteristics impedance is given by:- The value of propagation constant is given…

Q: Y = E(0,2,3,4,9,10,12,13) d (6,8,14) .Simplify using KMap. Q

A: K-map is used to minimized the expression . The K-map is arranged in such way that its differ by 1…

Q: O A transmission line operating at f = 1 GHz has Z0 = 100 N , a = 0.05 N„/m, ß = 1.5 rad/m. Find the…

A: Given Data: f = 1 GHz Zo = 100 ohm alpha = 0.05 Np/m beta = 1.5 rad/s

Q: A transmission line has the following per-unit-length parameters: L = 0.5 µH/m, C = 200 pF/m, R =…

A: Given Data: R = 4 ohm L = 0.5 uH C = 200 pF G = 0.02

Q: The open-circuit and short-circuit impedances measured at the input terminals of a transmission line…

A: Givenlength of transmission line l=4 mopen circuit impedance Zio=250∠-50° Ωshort circuit impedance…

Q: Q8) A transmission line has the following per unit length parameters: L-0.2 µH/m C=300 pF/m R=5 2/m…

A: Given data: L=0.2μH/mC=300 pF/mR=5ΩG=0.02S/mf=500 MHz

Q: 2- Transmission line 10m long has distributed parameters R = 5 Q /m, L = 6µH/m, G= 10 mS/m, and C =…

Q: uestion 8 "To determine the voltage regulation of a long line, which of the generalised constat…

Q: A 60 Hz, single-circuit, three-phase transmission line is 150 mi long. The line is connected to a…

Q: A lossless transmission line is 80 cm in length and operating at a frequency of 140 MHz. The line…

A: Given, Length=80cm=0.8m Frequency=f=140MHz Capacitance=C'=70×0.8=56pF Inductance=L'=0.4×0.8=0.32μH…

Q: B-For the lossless transmission lines circuit shown below, design the value of Rx for proper series…

A: Given figure,

Q: The components of the propagation constant are named as For long transmission line system, The…

A: Given *The components of the propagation constant are named as…

Q: A lossless transmission line, with characteristic impedance of 50 N and electrical 2 length of { =…

A: 2. A lossless line is characterized as a transmission line that has no line obstruction and no…

Q: A 50-N lossless line is terminated in Z, =R2= 30 N. Determine the following: determine the input…

A: For the given lossless line, ....... load impedance ......... line impedance ...............…

Q: A transmission line operating at 125 MHz has Z = 40 2, a = 0.02 (Np/m), and B = 0.75 rad/m. Find the…

A: This question belongs to power system . It is based on the concept of distortion less transmission…

Q: -4. A lossless transmission line has a characteristic impedance of 100 N and is terminated in a load…

Q: The parameters of a lossy transmission line are L' = 0.45 µH/m, R' = 0.15 2/m and w 5 x 10° rad/s.…

Q: For a one port network, explain the effect on the admittance frequency characteristics when it has a…

A: In the question, What is effect of frequency in admittance of path if Element is connected to…

Q: At an operating frequency of 300 MHz, it is desired to use a section of a lossless 50 N transmission…

A: Transmission line

Q: What is the input impedance of a 50 Ω short-circuit transmission line of length λ ⁄ 8, in ohms?

Q: A) Determine the primary constants, R, L, G, and C for a distortion-less line working at 300 MHz.…

Q: A certain transmission line operating at w = 10° rad/s has a = 8 dB/m, 8 = 1 rad/m, and Z, = 60 +…

A: Wave is function of space and time. The mode at which waveguide have lowest frequency is said to be…

Q: A certain transmission line operating at w = 10 rad/s has a = 8 dB/m, 8 = 1 rad/m, and Z, = 60 + j40…

A: The EM wave is formed when electric field is in contact with magnetic field. Ratio of transverse…

Q: The static wave ratio in a 300 ( N) lossless transmission line terminating at an unknown load…

A: GIVEN DATA:

Q: A certain transmission line operating at w 10 rad/s has a = 8 dB/m. 3 = 1 rad/m, and Z, = 60 + j40…

A: LOSSLESS TRANSMISSION LINE: A transmission line with no line resistance and no dielectric loss is…

Q: A 60-ohm distortionless transmission line has a capacitance of 0.15nF/m. The attenuation of the line…

A: Given data Z0=60 ΩC=0.15 nF/mα=1.15×10-3 Np/m i) Expression of characteristic impedance Z0=LC…

Q: The standing-wave ratio on a lossless 3002 transmission line terminated in an unknown load impedance…

Q: One end of an air lossless transmission line having the characteristic impedance of 75 Q and length…

A: Power generation, transmission, and distribution systems constitute a power system. The power…

Q: Q1: A transmission line has the following per-unit-length parameters: L = 0.5 µH/m, C = 210 pF/m, R…

A: Power System Network: A basic Power system network consists of Generation unit, Transmission unit…

Q: 2- Transmission line 10m long has distributed parameters R = 52/m, L = 6µH/m, G= 10 mS/m, and C = 25…

Q: From the given expressions of the parameters of medium length transmission line, which one will have…

A: The medium length transmission line parameters in nominal-T model are ABCD=1+ZY2ZY1+ZY2

Q: A 300Ω transmission line 150m long, operates at 400kHz with attenuation coefficient of 2.4 x10^(-3)…

A: A 300Ω transmission line 150m long, operates at 400kHz with an attenuation coefficient of 2.4…

Q: Consider the transmission line model below. Parameters R',L',G'.C' are given on a per length basis.…

A: In the solution i solve both telegraphee's equations i hope it helps you in concept building

Q: Transmission line 10m long has distributed parameters R = 5 Ω /m, L = 6µH/m, G = 10 mS/m, and C = 25…

A: (A): The characteristics impedance is:…

Q: ) Write ABCD Parameters of the nominal π model of the medium transmission line.

Q: For a one port network, explain the effect on the admittance frequency characteristics when it has a…

A: In the question, What is effect of frequency in admittance of path if Element(either indotor Or…

Q: What is the input impedance of a 50 Ω open circuit transmission line of length λ ⁄ 8, in ohms?

A: Solve as below

Question

The open-circuit and short-circuit impedances measured at the input terminals of an air-
spaced transmission line 4m long are 2502-50°N and 360220°2, respectively. (a)
Determine Z, a, and ß of the line. (b) Determine R, L, G, and C.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the charecterictics impedance, propagation constant and velocity of propagation at 600 KHz for a transmission line having L=0.5Mh/km and C=.08microfarad/km,and and negligible R and G.
Viva Questions:1. What is the difference between Primary and Secondary constants? 2.Define Transmission line Input Impedance?
)A 60-ohm distortionless transmission line has a capacitance of 0.15nF/m. The attenuation of the line 1.15*10-3 Np/m. Calculate: (i) The line parameter resistance, inductance and conductance per meter of the line, (ii) Voltage at a distance of 1Km and 4Km with respect to sending voltage.
In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit. Select one: True False
Obtain the input impedance expression Zent for a transmission lineterminated in short circuit
When operating at a frequency of 2 kHz, a cable has an attenuation of 0.25 Np/km and a phase shift of 0.20 rad/km. If a 5V rms signal is applied at the sending end, determine the voltage at a point 10 km down the line, assuming that the termination is equal to the characteristic impedance of the line.
1. We have a two-wire overhead transmission line, powered by a constant voltage source of 700 V. The values for the inductance of the conductors are 2.348x10-3 H/km and the capacitance values are 6.325x10-9 F/km. Assuming an ideal (lossless) line and its length of 130 km, determine the speed at which it propagates. PLEASE MAKE IT DIGITAL BECAUSE HAND WRITING GETS UNDERSTANDING
Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
Consider the transmission line of Problem 5.18. (a) Find the ABCD parameters of the line when uncompensated. (b) For a series capacitive compensation of 70 (35 at the sending end and 35 at the receiving end), determine the ABCD parameters. Comment on the relative change in the magnitude of the B parameter with respect to the relative changes in the magnitudes of the A, C, and D parameters Also comment on the maximum power that can be transmitted when series compensated.
Given a telephone transmission line of 100 mile long has Z,=685-j92Q, 0a=0.00497 neper/mile and f=0.0352 rad/mile work at 1000Hz. If Z=2000Q and Eg=10Vrms with Z:=700Q, find the sending end impedance, voltage, current, and power.
"A coaxial cable has a foam polyethylene insulator whose velocity factor is 0.7. If the inner diameter of the outer conductor is 4 times the diameter of the inner conductor, what is the characteristic impedance of the transmission line? Use four decimal places (if the answer is not an integer)."
Optical Fibre communication link: Discuss the results in regards to power transmitted (dBM) Vs The Optical Length. Clear explanation