A symmetrical, passive, reciprocal and lossless two-port network has a Z, (real) characteristic impedance at both ports. When the output port (port-2) is terminated with Z11 = Z, and Z12 = 52, loads, the reflection coefficients of I = 0.5 and î2 = 0 are measured from the input port (port-1), respectively. Determine the scattering matrix (S-parameters) of the two-port network by using the relation below. = S11 + 1- S„f

A symmetrical, passive, reciprocal and lossless two-port network has a Z, (real) characteristic impedance at both ports. When the output port (port-2) is terminated with Z11 = Z, and Z12 = 52, loads, the reflection coefficients of I = 0.5 and î2 = 0 are measured from the input port (port-1), respectively. Determine the scattering matrix (S-parameters) of the two-port network by using the relation below. = S11 + 1- S„f

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A lossless transmission line is terminated by an open circuit. An incident signal travels from the source to the load gets reflected and travels all the way back to the source. It takes 4 microseconds for the signal to go from the source to the load and then from the load to the source. What is the length of the line (in m) if the propagation velocity is equal to the speed of light (in m/s)? Enter only the numerical value. No need for the unit. Use four decimal places (if the answer is not an integer).
I want a solution for branches A and B, pleaseA) Determine the primary constants, R, L, G, and C for a distortion-less line working at 300 MHz. Given that the line has characteristic impedance, Zo=750, attenuation constant a=0.12Np/m, and wave velocity, v=1.4×10 m/sB) A lossless transmission line used in a TV receiver has a capacitance of 50 pF/m and an inductance of 200 nH/m. Find the characteristic impedance for sections of a line 10 meter long and 500 m long.
)A 60-ohm distortionless transmission line has a capacitance of 0.15nF/m. The attenuation of the line 1.15*10-3 Np/m. Calculate: (i) The line parameter resistance, inductance and conductance per meter of the line, (ii) Voltage at a distance of 1Km and 4Km with respect to sending voltage.
For the lossless transmission line shown below, the T.L. was previously charged to E=128V and the switch is closed at t=0. If Zo= 150 ohms and RL= 450 ohms, find the following VRL at t=3To VRL at t=To First reflected voltage from the load (Vr-)
A 100 ohm transmission line powered by a 1 GHz source and terminated with a load impedance of ZL = 60 + j50 ohms will be matched with an open-circuit series side. What should be the length, in cm, of the serial lateral line calculated using the Smith diagram?
Optical Fibre communication link: Discuss the results in regards to power transmitted (dBM) Vs The Optical Length. Clear explanation
. Suppose two hosts A and B, are separated by 10,000 kilometers and are connected by a directlink of R = 1 Mbps. Suppose the propagation speed over the link is 2.5 x 108 meters/sec.a. Calculate the "bandwidth-delay product", R.tprop.b. Consider sending a file of 400,000 bits from host A to B. Suppose the file is sent continuouslyas one big message. What is the maximum number of bits that will be in the link at any giventime?c. Provide an interpretation of the bandwidth-delay product.d. What is the width (in meters) of bit in the link? Is it longer than a football field?e. Derive a general expression for the width of a bit in terms of the propagation speed s, thebandwidth R, and the length of the link d
Consider the bandwidth of the line is 1.2 Mbps, packet size is 1 KB and round-trip time is 50 msec. What is the link utilization in stop and wait? a) 10.8% b) 14% c) 12% d)13.5%
Suppose two hosts A and B, are separated by 10,000 kilometers and are connected by a direct link of R = 1 Mbps. Suppose the propagation speed over the link is 2.5 x 10^8 meters/sec.a. Calculate the "bandwidth-delay product", R.tprop.b. Consider sending a file of 400,000 bits from host A to B. Suppose the file is sent continuously as one big message. What is the maximum number of bits that will be in the link at any given time?c. Provide an interpretation of the bandwidth-delay product.d. What is the width (in meters) of bit in the link? Is it longer than a football field?e. Derive a general expression for the width of a bit in terms of the propagation speed s, the bandwidth R, and the length of the link d.
Question 777 Consider a two-port network comprising a 25Ω resistor connected in shunt. (a) Write down the scattering parameters of the two-port using a 50Ω reference impedance. (b) From the scattering parameters derive the ABCD parameters of the two-port Full explain this question and text typing work only thanks
A microstrip line is composed of zero thickness copper conductors on a substrate having εr = 8.4, tan = 0.0005 and thickness 1.5 mm. if the line width is 0.5 mm,and operated at 6Ghz, determine the characteristic impedance.
380 kilovolts 50 hertz length of a transmission line 250 kilometers given as.Steel core aluminum conductors were used in a three-phase transmission line and the diameter of these conductors was determined 20 millimeters given as. The roughness coefficient of these conductors is 0.9 , If the phase gaps are 5 meters . Average air temperature and air pressure along the line, respectively 25 °C and 750 mmHg is. Under these given conditions, the line Assuming that it is operated at 494 kilovolts voltage; a) Calculate the corona loss per kilometer of a phase of the transmission line using the peek formula ? b) Calculate the total corona losses that will occur in this transmission line using the peek formula. (Result will be entered in MegaWatts) ?