The orthogonal cutting of steel is done with 10° rake tool with a depth of cut of 4mm feed rate of 0.4mm/rev. The cutting speed is 200m/min. The chip thickness ratio is 0.35. The vertical cutting force is 1200N and the horizontal cutting force is 700N. Calculate from the Merchant's theory, the various work done in metal cutting and shear stress.

The orthogonal cutting of steel is done with 10° rake tool with a depth of cut of 4mm feed rate of 0.4mm/rev. The cutting speed is 200m/min. The chip thickness ratio is 0.35. The vertical cutting force is 1200N and the horizontal cutting force is 700N. Calculate from the Merchant's theory, the various work done in metal cutting and shear stress.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an orthogonal turning process, the chip thickness is 0.32 mm , feed is 0.2 mm/rev, then calculate the cutting ratio.
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
Assuming that the coefficient of friction is 0.25, calculate the maximum depth of cut forturning a hard aluminium alloy on a 15-kW lathe (with a mechanical efficieny of 80%) at awidth of cut of 6 mm, rake angle of 0˚, and a cutting speed of 90 m/min, shear strength of 150 MPa.
A flat milling operation will be carried out with a horizontal milling machine, in a piece of 250 mm in length and 50 mm in width, using a felicoidal bur with a diameter of 75 mm, with 10 teeth. If the feed per tooth is 0.2mm, and the cutting speed is 0.75 m / s, how would you determine the speed of metal removal to remove 6 mm from the surface of this piece?
In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool. the cutting velocity is 90 m/min The feed is 0.24 mm/rev and the depth of cut is 2 mm. The chip thickness obtained is 0.48 mm If the orthogonal rake angle is zero and the principal cutting edge angle is 90° Calculate the shear angle in degree.
Find the time required for one full cut on a work piece of 350mm long and 20 mm in diameter. The cutting speed is 30 meters per minute and the feed is 0.5mm per revolution. Average. SHOW YOUR SOLUTION WITH DRAWINGS
A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.
In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut. Can u help me please?
Draw the forces and angles involved in the cutting process and calculate shear angle (0), friction coefficient and tangential force if ,cutting force = 80 kN, resultant of forces =100kN, friction force=75kN, rake angle =20° undeformed chip thickness = 0.65mm and deformed chip thickness = 0.72mm
Assume that, in orthogonal cutting, the rake angle is 20 and the friction angle is 35 at thechip-tool interface. Determine the percentage change in chip thickness when the frictionangle is 50. Note that Merchant’s equation is more preferable.
Find the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by using a carbide insert. If the approach length and over run length is taken as 5 mm, Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
A tool with zero rake angle used in orthogonal cutting when its clearance angle a is changed from 10 to 7 deg, Calculate the approximate % change in the life of the tool.