The output model of an operational amplifieris modeled as:Select one:a. A dependent current source in serieswith a resistorO b. A dependent voltage source in parallelwith a resistorc. A dependent voltage source in serieswith a resistord. An independent voltage source inseries with a resistor

The electrical equivalent model for the operational amplifier is:

The output model of an operational amplifier is modeled as: Select one: a. A dependent current source in series with a resistor b. A dependent voltage source in parallel with a resistor c. A dependent voltage source in series with a resistor d. An independent voltage source in series with a resistor

The output model of an operational amplifier is modeled as: Select one: a. A dependent current source in series with a resistor b. A dependent voltage source in parallel with a resistor c. A dependent voltage source in series with a resistor d. An independent voltage source in series with a resistor

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Convert the inverting amplifier shown to thetransresistance amplifier as shown(66) using a Nortontransformation of vi and R1. What are the expressionsfor iTH and RTH? Write a expression forthe gain vo/vi.
An amplifier is formed by cascading two operational-amplifier stages, as shown (a). (a) Replace each amplifier stage with its two-port representation. (b) Use the circuit model from part (a) to find the overall two-port representation (Av, Rin, Rout) for the complete twostageamplifier. (c) Draw the circuit of the two-port corresponding to the complete two-stage amplifier.
The figure below shows an inverting amplifier connected to a load RL. Determine the power gain of the amplifier. power gain for the amplifier, G, is defined as the power ratio that reaches the load RL versus the power supplied by the source VS.
A certain amplifier has an open-circuit voltage gain of unity, an input resistance of 1 MΩ and an output resistance of 100 Ω. The signal source has an internal voltage of 5 V rms and an internal resistance of 100 kΩ. The load resistance is 50 Ω. If the signal source is connected to the amplifier input terminals and the load is connected to the output terminals, find the voltage across the load and the power delivered to the load. Next, consider connecting the load directly across the signal source without the amplifier, and again find the load voltage and power. Compare the results. What do you conclude about the usefulness of a unity-gain amplifier in delivering signal power to a load?
Suppose we have a resistive load that varies from 5 kΩ to 10 kΩ .We connect this load to an amplifier, and we need the voltage across the load to vary by less than 1 percent with variations in the load resistance. What parameter of the amplifier is important in this situation? What range of values is allowed for the parameter?
The voltage transfer characteristic for an operational ampliﬁer shown (a) What are the values of gain and offset voltage for this op amp? (b) Plot voltage gain A versus vid for the ampliﬁer voltage transfer characteristic.
The amplifier as shown has R2 = 68 kΩ and R1 = 2.7 kΩ. What are the valuesof Av A, Av B, Av C, RinA, RinB, RinC, and RoutA, RoutB, RoutC, for the amplifier equivalent circuit as shown.
Suppose the output signal voltage from the amplifier is 35 times the input signal voltage. If the imput and output impedance are both pure resistances of the same value, what is the gain
In the ideal operational amplifier circuit given in the figure, a) Find the voltage V0. b) Find the I0 current. y = 2
Suppose that each output channel of a computer’ssound card can be represented by a 1-V ac sourcein series with a 32-Ω resistor. Each channel ofthe amplifier in the external speakers has an inputresistance of 20 k , and must deliver 10 W intoan 8-Ω speaker. (a) What are the voltage gain, currentgain, and power gain required of the amplifier?(b) What would be a reasonable dc power supplyvoltage for this amplifier?
If an inverting amplifier takes input supply voltage of 20V, input resistance and feedback resistance are 15 ohm and 60 ohm respectively then find its output voltage. NOTE : KINDLY ELABORATE BRIEFLY
(a) Design a single-stage inverting ampliﬁer with a gain of 46 dB using an operational ampliﬁer. The input resistance should be as low as possible while achieving the op amp output drive capability mentioned here. The ampliﬁer must be able to produce the signal vo = (10sin1000t) V at its output when an external load resistance RL ≥ 5k Ω is connected to the output of the ampliﬁer. You have an operational ampliﬁer available whose output is guaranteed to deliver ±10 V into a 4-kΩ load resistance. Otherwise, the ampliﬁer is ideal. (b) If the ampliﬁer input signal is vi = V sin1000t, what is the largest acceptable value for the input signal amplitude V? (c) What is the input resistance of your ampliﬁer?