The output X of a logic circuit depends on the input signals A, B and C as in th following logic expression: X = (A + B + C)C (а) Draw the logic diagram using only 2-input gates. Label each gate output. (b) Based on the label in (a), show the calculation for each gate outputs if i. A = 0, B = 0 and C = 0. ii. A = 0, B = 0 and C = 1. (c) Build a truth table for the following input signal combinations by including th output for each gates, according to the label in (a). A В C 1 1 1 1 1 1

The output X of a logic circuit depends on the input signals A, B and C as in th following logic expression: X = (A + B + C)C (а) Draw the logic diagram using only 2-input gates. Label each gate output. (b) Based on the label in (a), show the calculation for each gate outputs if i. A = 0, B = 0 and C = 0. ii. A = 0, B = 0 and C = 1. (c) Build a truth table for the following input signal combinations by including th output for each gates, according to the label in (a). A В C 1 1 1 1 1 1

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

a) Design a logic circuit with three inputs A, B, C and an output that goes LOW only when A is HIGH while B and C are different. Draw and upload the circuit if you can, or at least describe it in words. b) Which logic gates produce a 1 output in the disabled state? c) Which logic gates pass the inverse of the input signal when these gates are enabled? d) What is the normal resting state of the SET’ and RESET’ inputs of a latch circuit (the prime is same as bar)? What is the active state of each input? e) What is the normal resting state of the NOR latch inputs? What is the active state?
Solve the following in Boolean Algebra: (BC'+A'D)(AB'+CD') A. Simplify the given function using Boolean simplification. B. Draw the logic diagram of the given equation. C. Draw the logic diagram of the simplified equation. D. Give the number of of logic gates used in the given design E. Give the number of logic gates used in the simplified design.
Q1. Design a 4-input, one output combinational logic circuit for the following input-output conditions: a) If the number of 1’s in inputs is more than or equal to 2 then the output is 1 ?. b) If the number of 1’s in inputs is less than 2 then the output is 0 ?.
A coin-operated cold drink dispenser will provide cold drink (D) under the following conditions: The correct coin (C) is inserted AND A paper cup is in position (P) AND The selector is set t Orange (O) OR Sprite (S) OR Lemonade (L) Write the Boolean expression for the output of the dispenser. Represent the operation of the dispenser in logic circuit 4 get a logic circuit to mimic corporate checking system for operators of a company
Act 1 problem solving this is a logic circuits and design laboratory subject please help me with this and screenshot all the solution and answers 2. What is the largest binary number that can be expressed with 16 bits? What are the equivalent decimal and hexadecimal numbers? Answer: 16 bits = ________= _______10 = ______16 3. Represent the decimal number 6,248 in: (a) BCD = (b) excess‐3 code = (c) 2421 code =
B) A coin-operated cold drink dispenser will provide cold drink (D) under the following conditions: The correct coin (C) is inserted AND A paper cup is in position (P) AND The selector is set t Orange (O) OR Sprite (S) OR Lemonade (L) Write the Boolean expression for the output of the dispenser. Represent the operation of the dispenser in logic circuit 4 get a logic circuit to mimic aorporate checquing system for operatore of a compnny
Draw the output waveform C and D, given the input waveforms A and B as shown belowfigure 2.Figure 2b) Verify the result from part (a) by any using simulation tools. (Screen shoot only for thefollowing input cases: when (A=0, B=0), (A=1, B=0) and (A=0, B=1). c) For the logic circuit given in Figure 3, obtain the output expression for ?
1) Design the logic gates that compare (3) bit binary numbers that are "equal" or "not equal." A0 B0 A1 B1 A2 B2 2) Derive the logic equations for both outputs 3) What type of circuit/system can this be used in an application you could create?
Answer the following questions: If a 3-input XOR gate has eight input possibilities, how many of those possibilities will result in a HIGH output? What type of logic circuit is represented by figure 4 shown below? Name the gate whose output is HIGH if and only if all the inputs are LOW If a JK latch has J=1, K=0 initially. When the K input goes high, what will be the output?
Design a logic circuit that controls the passage of a signal A according to the following requirements:1. Output X will equal the value of A ( 0 or 1)when control inputs B is low and C is high.2. X will remain HIGH for all other input combinations. A=MSB C=LSB
A three input logic function will provide a logic high output only when all of the inputs are logic highs or when all of the inputs are logic lows. For all other input possibilities, a logic zero is provided on the output. What is the logic expression? A. A'B'C'+AB'C' B. Y=A'B'C'+ABC C. ABC'+AB'C D. A'B'C'+AB'C
Book used is Digital Logic with Verilog Design by Brown & Vranesic. Study the counting circuit diagram below and answer the following questions: a. Based on the circuit drawing, is the Clock Positive-Edge Triggered or Negative-Edge Triggered? b. How was this determination made? c. What are the minimum and maximum valkues of the circuit? Explain. d. There are 3 grayed out boxes we refer to this symbolic use as _____________. Why are these used in circuit design?