The production of more than one useful form of energy (such as process heat and electric power) from the same energy source is called . The most common is the The overall thermal efficiency of a power plant can be increased by using a gas-steam combined cycle where a gas-turbine cycle operates at the high-temperature range and a steam-turbine cycle at the low-temperature range. Steam is heated by the high-temperature exhaust gases leaving the gas turbine. have a thermal efficiency than the steam- or gas-turbine cycles operating alone.

The production of more than one useful form of energy (such as process heat and electric power) from the same energy source is called . The most common is the The overall thermal efficiency of a power plant can be increased by using a gas-steam combined cycle where a gas-turbine cycle operates at the high-temperature range and a steam-turbine cycle at the low-temperature range. Steam is heated by the high-temperature exhaust gases leaving the gas turbine. have a thermal efficiency than the steam- or gas-turbine cycles operating alone.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a heat engine is operating on a steady‐flow Carnot cycle with water asthe working fluid. The water mass flow rate in cycle is 0.5 kg/s. The cyclemaximum per minimum absolute temperatures ratio is 2.5. The quality of wateris 1 at the beginning of the heat‐rejection process and 0 at the end and theambient temperature is 35°C. Show the cycle on a T‐s and P‐v diagrams relativeto the saturation lines, and determine (a) the thermal efficiency, (b) thepressure at the turbine inlet, (c) maximum temperature, minimum pressure (d)the network output, (e) the entropy changes in all processes, and (f) the actualnetwork output with second law efficiency of 45%.
A 600-MWe power plant has an efficiency of 36 % with 15% of the waste heat beingreleased to the atmosphere as stack heat and the other 85% taken away in the coolingwater. Instead of drawing water from a river, heating it, and returning it to the river, this plant uses an evaporative cooling tower wherein heat is released to the atmosphere as cooling water is vaporized. At what rate must 15 °C makeup water be provided from the river to offset the water lost in the cooling tower?
Consider a gas turbine that has a pressure ratio of 6 and operates on a Brayton cycle with regeneration between the temperature limits of 20°C and 900°C. If the specific heat ratio of the working fluid is 1.3. Determine the highest thermal efficiency, in %, that this turbine can have.
A basic Rankine steam power plant uses an adiabatic turbine that operates with inlet steam at 6.80 MPa6.80 MPa and 550.0 ∘C.550.0 ∘C. The exhaust steam enters the condenser at 50.0 ∘C50.0 ∘C with a quality of 0.960. Saturated liquid water leaves the isobaric condenser and is pumped to the boiler. Mass flow through the cycle is 1.850 kg/s.1.850 kg/s. Neglecting pump work and kinetic and potential energy changes, determine: the work interaction term of the turbine: © Macmillan Learning A basic Rankine steam power plant uses an adiabatic turbine that operates with inlet steam at 6.80 MPa6.80 MPa and 550.0 ∘C.550.0 ∘C. The exhaust steam enters the condenser at 50.0 ∘C50.0 ∘C with a quality of 0.960. Saturated liquid water leaves the isobaric condenser and is pumped to the boiler. Mass flow through the cycle is 1.850 kg/s.1.850 kg/s. Neglecting pump work and kinetic and potential energy changes, determine: the work interaction term of the turbine: the thermal efficiency of…
A 286-MW steam power plant operates on the Rankine cycle but with turbine and pump efficiencies of 90%. The steam enters the turbine at 10,000 kPa and 550°C. It discharges to the condenser at 50 kPa. Determine the mass fraction of steam that condenses at the turbine exit in percent.
A gas-fired power plant operating on a Brayton cycle draws in 9.0 kg/s of atmospheric air, initially at 300 K and 100 kPa, in order to generate 1.7 MW of electricity. If the combustion chamber adds heat by burning 0.07 kg/s of fuel with a heating value of 46.1 MJ/kg, and as a result the air entering the turbine is at a temperature of 861 K, determine the back work ratio of this device to 2 decimal places. You may treat the added mass of the fuel as negligible. Take the cp of air to have a constant value of 1.005 kJ/(kg K) throughout the whole cycle, and its ratio of specific heats k can be assumed to take the value 1.4.
Consider a Carnot heat-engine cycle executed in a closed system using 0.01 kg of refrigerant-134a as the working fluid. The cycle has a thermal efficiency of 15 percent, and therefrigerant-134a changes from saturated liquid to saturated vapor at 50°C during the heat addition process. Determine the net work output of this engine per cycle.
A 3 Megawatt steam power plant operates at a steam engine pressure of 220 psia, 550 °F and at exhayst pressure of 5 psia. The steam consumption is 62,700 lb/hr. Calculate the indicated engine efficiency if the combined electrical and mechanical efficiency is 70%
This is thermodynamics. Please complete solution A power plant operating on a Rankine cycle has steam entering the turbine at 500 °C and 2 MPa. The turbine and pump efficiencies are 85 and 90 percent, respectively. If the water enters the pump at 10 kPa at a rate of 162,000 kg/hr, calculate the (a) actual turbine power, (b) actual pump power, (c) actual heat added to the water in the boiler, (d) actual cycle thermal efficiency, and (e) actual condition of steam leaving the turbine.
A steam power plant operating on a regenerative cycle, as illustrated in Fig. 8.5, includes two feedwater heaters. Steam enters the turbine at 6500 kPa and 600°C and exhausts at 20 kPa. Steam for the feedwater heaters is extracted from the turbine at pressures such that the feedwater is heated to 190°C in two equal increments of temperature rise, with 5°C approaches to the steam-condensation temperature in each feedwater heater. If the turbine and pump efficiencies are each 0.80, what is the thermal efficiency of the cycle, and what fraction of the steam entering the turbine is extracted for each feedwater heater? kindly answer it with full explanation of the solution, thankyou
Consider a steam power plant operating on a simple Rankine cycle. Steam enters the turbine at 15 MPa and 650°C and is condensed in the condenser at a pressure of 15 kPa. Assuming an isentropic efficiency of 84% and 86% for the pump and turbine, respectively, determine the actual Wnet (kJ/kg). (Use 2 decimal places for the final answer.)
is the net work for any cycle Zero? why