The pump-turbine system in the figure draws water from the upper reservoir in the daytime to produce power for a city. For a design flow rate of 33.4 cfs (ft³/s), the friction head loss is 17 ft. Estimate the power in horsepower extracted by the turbine (W₁ = yQht). Use y = 62.4 lbf/ft³; 1 hp = 550 ft·lbf/s) A. 409.3 B. 538.1 C. 473.7 1 Water at 20°C, Pump- turbine D. None of the above Z₁ = 150 ft Z₂ = 25 ft

The pump-turbine system in the figure draws water from the upper reservoir in the daytime to produce power for a city. For a design flow rate of 33.4 cfs (ft³/s), the friction head loss is 17 ft. Estimate the power in horsepower extracted by the turbine (W₁ = yQht). Use y = 62.4 lbf/ft³; 1 hp = 550 ft·lbf/s) A. 409.3 B. 538.1 C. 473.7 1 Water at 20°C, Pump- turbine D. None of the above Z₁ = 150 ft Z₂ = 25 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A sluice gate, as shown in Figure Q1, is used to control the upstream water level in a4 m wide rectangular channel. The water discharge in the channel is 12 m3/s. Given the water depth at 1 is 2.4m use the Specific Energy equation to findthe water depth (to 1 decimal place) at 2.
Water flows from an upper reservoir to a lower one while passing a turbine as shown. 1. Compute the total head loss due to friction when the discharge is 150 lit/s. a. 4.25 m b. 3.84 m c. 5.67 m d. 2.54 m 2. Find the velocity of water. a. 2.05 m/s b. 4.12 m/s c. 3.06 m/s d. 6.57 m/s 3. Find the power input of the turbine. a. 213.5 kW b. 210.6 kW c. 115.2 kW d. 356.2 kW
A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B, as shown in Figure . The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe, and the head loss from 2 to B is fifteen times the velocity head in the 100-mm diameter pipe. 1. Compute the Power delivered by the pump in kw ( A. 79.07 , B. 48.10 C. 13.08 , D. 57.23) 2. Compute the Pressure head at point 1 in m. ( A. 85.96 , B. 19.74 C. 245.09 , D. 45.90) 3. Pressure head at point 2 in m. ( A. 104.51 , B. 246.67 C. 57.84 , D. 12.69)
An open rectangular tank 3.8m high, 2.5m wide and 6m long is filled with water at a depth of 2.2m. If it is accelerated at 2.3 m/s^2 and is moving at a plane inclined 15 degrees from the horizontal, determine the following: a. acceleration of the vessel along the horizontal; and b. angle of fluid inclination. Note: Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3.
3 .Consider the incompressible flow of an ideal fluid having a density ρ = 1600 kg / m3 (figure 3). We give: P1 = 2 105Pa, P2 = 3 105Pa, V2 = 1 m / s and V1 = 0.5m / s. Determine the net power of the pump to ensure a volume flow Qv = 0.01 m3 / s.
9. The depth of flow of water at a section of a rectangular channel of width 2 m is 0.3 m. The discharge through the channel is 1.5 m3/s. Determine the height of hydraulic jump and loss of energy per kg of water.
The crank and connecting rod of a theoretical steam engine are 0.4 m and 1.6 m long, respectively. The crank makes 180 rpm in clockwise direction. When it has turned 45° from the inner dead center position, determine the: a) Velocity of piston, b) Angular velocity of connecting rod
HYDRAULICS & ELECTRO-HYDRAULICS Calculate the pressure due to a column of 10.0m of (a) water, (b) mercury of sp. gr. 13.6, and (c) an oil of sp. gr. 0.9. Take density of water =1000 kg/m3.
A supply of water to reservoir C is drawn from two open reservoirs A and B by pipe network shown in the figure below. The elevation of water in both A and B is 10 m above the level in C. The friction factor may be assumed to be a constant with a value of 0.02. If the valve on the pipe from reservoir B is initially closed, determine the rate of flow from reservoir A, in m choices 0.00416 0.00306 0.01008 0.00702 PIPE AB BD CD LENGTH (m) 100 200 300 DIAMETER (mm) 50 80 100
In Fig.2, A Pelton wheel has a mean bucket speed (U) of 89 m/s with a jet of water flowing at the rate of 1 m3/s under a head of 270 m. The buckets deflect the jet through an angle of 170º. Calculate the power delivered to the runner and hydraulic efficiency of the turbine. Take Cv = 0.98 , V= Cv root of 2gH , workdone per second by the jet on the runner = ρaV1 (Vw1 + Vw2) x U and Hydraulic efficiency ηh = 2 U (Vw1 + Vw2)/V12
11.34. If the pressure at point A in the figure is 300 kPa, compute the volume flow rate of water at delivered to the tank.
Water leaving the nozzle at a velocity of 4350 m/min with a volume flow rate of 0.736 m³ . if the density of water is 0.000997 kg/cm³ . How will you determine the potential for power generation in a hydraulic turbine .