The rate of flow of water entering a pipe is 100kg/min at a temperature of 100 °C and pressure of 2 bar. The length of the pipe is given as 9ft and the diameter is given as 2in. Determine the rate of work done at the entrance of pipe. Take the density of water as 961.5 kg/m³.

The rate of flow of water entering a pipe is 100kg/min at a temperature of 100 °C and pressure of 2 bar. The length of the pipe is given as 9ft and the diameter is given as 2in. Determine the rate of work done at the entrance of pipe. Take the density of water as 961.5 kg/m³.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 49P

See similar textbooks

Related questions

Q: The inclined pipe shown in the figure is used to carry oil (p = 900 kg/m³, μ = 9x10-3 Pa.s) The pipe…

A: Solution: Given: ρ=900 kg/m3 μ=9×10-3Pas D = 20 cm =0.2 m L = 300 m V = 3 m/s

Q: Calculate the pressure and speed of water at points b and c as shown.

A: ASKED: To determine the pressure and speed of water at points B and C. Given, Pressure at A (PA) =…

Q: The water in the pipe given in the Figure Flows uniformly in sections I and 2. 1. Pipe diameter in…

A: Given information in question Diameter 1 = 20 cm V1 = 20 m/s Diameter 2 = 4 cm Density of fluid =…

Q: . Find the approximate height of water upstream of the dam or the headwater in meters, such that an…

A: Thank you for the question . As per honour code we will answer the first question since exact one…

Q: (3) An open jet of water at 20 °C exits a nozzle into sea-level air and strikes a stagnation tube,…

A: Consider the free body diagram ; Given data Pressure at section-1 (P1) =110kpa…

Q: Water (P =1000 kg/m , p=1.59x108 kg /m.s) is flowing with the velocity of 0.25 m/s through a smooth…

A: i. Given data-

Q: 1.) convert a pressure head of 15 m of water to meters of oil (sp. gr. =0.75). 2.) Convert a…

Q: A small drop of water at 20°C is in contact with the air and has diameter 0.2 mm. What is the excess…

A: GIVEN Small drop of water Temperature = 20°C Diameter, d = 0.2 mm = 0.0002 m To Determine Excess…

Q: In the figure, a pipe system in parallel is with a total flow of 400lit/s. determine the division of…

Q: Compute the height of capillary rise for water in a tube having a diameter of 0.05 mm (in SI units).

A: Given: The diameter of the tube is 0.05 mm.

Q: Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the…

A: Given:- head loss from point 1 to point 2= 600mm diameter=150mm SG of oil=0.84 flow=17L/s To find:-…

Q: Water is flowing in a 300 mm pipe a pitot tube is connected to determine the velocity, if the gauge…

A: Find velocityv=2ghh=xshgsw-1h=0.075m13.61-1h=0.945m

Q: Water is flowing in the straight 100mm diameter coated cast iron as shown in the figure. Due to…

A: Given data: D=100 mm =0.1m L=180 m

Q: Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as…

A: Given n= 0.013 Discharge, Q= 12 cfs Length of pipe = 160 ft Diameter of pipe = 4 inches

Q: Pitot Pipe By connecting a mercury pressure gauge to a vertical pipeline through which water is…

A: step 1-

Q: Two adjacent rectangular tanks hold water as shown in the figure below. Considering the dimensions…

A: step1-

Q: empt in Progress The homogeneous gate shown in the figure below consists of one quarter of a…

Q: For water and oil flow in horizontal pipelines, a double U-tube manometer is connected betwe shown…

A: To find pressure between water and oil pipe

Q: 3) Water flows through the Venturi meter shown in the figure below. D1= 6 in, D2= 3 in and h= 2 in.…

Q: An orifice meter of 0.15 m diameter is fitted in a 0.3 m diameter pipe to measure the flow rate of…

Q: The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be…

A: The given data is: Q=SN/100=0.21 m3/s λ=SN/1000=0.021 L=SN*100=2100 m

Q: SUBJECT IS HYDRAULICS SHOW DETAILED AND COMPLETE SOLUTION USED 3 DECIMALS FOR THE FINAL ANSWER A…

Q: What is the head loss in pipe due to friction over the length of 30 km, if the diameter of pipe is…

A: Given data: Length, L = 30 km = 30×103 m Diameter, d = 80 cm =0.8 m Velocity, v = 30 cm/s = 0.3 m/s…

Q: A cylindrical tank contains air, oil and water, as shown; the air is under gage pressure p = 60 kPa.…

Q: Water flows through a 75 mm diameter pipe at a velocity of 3 m/s. Find the mass flow rate in kg/sec…

Q: A horizontal venturi meter 45 cm by 60 cm is used to measure the flow of air through a 60 cm…

Q: 4m A 4-meter-diameter cylindrical tank contains oil and water as shown in the figure. At the bottom…

Q: Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as…

A: Given data, n= 0.013 Discharge, Q= 12 cfs Length of pipe = 160 ft Diameter of pipe = 4 in To find…

Q: diameter of pipe = 200mm Cc = 0.61 Cv = 0.97 Considering the figure, what is the flow of water?

Q: Water entering through 5 ft long and 1 inch diameter pipe has a flow rate of 100 kg/min at a…

A: Given: Length, L = 5 ft Diameter, D = 1 in Mass flow rate, m = 100 kg/min Temperature, T = 100°C…

Q: The gate pressure of the air in the tank shown below is measured to be 50 .kpa. Determine the…

A: γw=10 KNm3γhg=13.6γwγoil=0.72γw now consider the point 30 cm below the container as reference and…

Q: Water and oil flow in two pipeline in figure below using the double U-tube manometer as connected…

A: From the Very Basic rinciple: Pressure is Same at Same Horizontal Level. So, The Pressure at a…

Q: Question: Water is flowing in the vertical pipe system shown in the figure. Water exits to the…

A: The given figure is shown below:

Q: Water flows steadly from the large open tank shown below. if viscous effects are negigble, determine…

A: We know velocity from tank filled with water is given byv=2gz1-z2so,z1-z2=4m

Q: Solve the following problems 1. With 30 liters/sec of water flowing as shown in figure, what…

Q: Find the depth of the water in the tank, H, and the manometer reading, h, if the hydrostatic force…

Q: A roof tank supplies water as shown in Figure 1. Calculate the minimum height (H) in metre required…

A: Given - Static head = 1.5m Velocity = V1.01/s Formula used - Htotal = Static headHs + Dynamic…

Q: Water floes through a circular pipe with a constant radius of 8cm. The speed and pressure at point a…

Q: Mechanics: (a) Convert a pressure head of 4.60 m of water to meters of oil, s.g. 0.750. (b) Convert…

A: Pascal's principle, also called Pascal's law, in fluid (gas or liquid) mechanics, statement that, in…

Q: Determine the rate of flow of water through a pipe of diameter 20 cm and length 50 m when one of the…

Q: (b) Water flows from a pressurized tank through a pipe and rises to the surrounding as shown in…

A: ii) Introduction : Flow velocity is a vector field that is used to mathematically characterise fluid…

Q: The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The…

Q: Q1: A pressurized tank is providing water for a fountain at a steady flow rate, showing in the…

Q: Consider the piping system shown . The average speed of water flowing through the 600-mm-diameter…

A: What is the volume flow rate of water in the piping system? What is the average speed of water in…

Q: 1. Water at 10°C is flowing at 0.075 m3/s. Calculate the weight flow rate and the mass flow rate.

Q: Determine the average velocity of water at the nozzle exit. The average velocity of water at the…

A: given diameter of the hose Dh= 1 in average velocity of hose Vh = 5.8 ft/sec diameter of nozzle…

Q: Water flows through a horizontal pipe at a rate of 2.4 gallons per second. The pipe consists of two…

A: Given data: water flow rate, Q=2.4 gallons per second = 554.4 cubic inch per second Area of bigger…

Q: EXAMPLE 10.1 The internal and external diameter of the impeller of a centrifugal pump are 300 mm and…

A: D1=300mm D2=600mm N=1000rpm

Concept explainers

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.

Question

Please help!

The rate of flow of water entering a pipe is 100kg /min at a temperature
of 100 °C and pressure of 2 bar. The length of the pipe is given as 9ft
and the diameter is given as 2in. Determine the rate of work done at the
entrance of pipe. Take the density of water as 961.5 kg/m³.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

diameter of pipe = 200mm Cc = 0.61Cv = 0.97 Considering the figure, what is the flow of water?
A 12-inch by 6-inch Venturi meter is installed in a vertical pipeline carrying water as shown inthe Figure C. The flow is upward through the meter. A differential manometer containing fluid,with sp.gr 1.67, is attached to inlet and throat, the difference z in gage levels being 5.76 ft.Neglecting loss of head, write energy equation from inlet to throat of meter. Also write stepby step equation of the differential gage between inlet and throat and combine the twoequations to compute the discharge
(b) FIGURE Q2 shows a siphon used to drain water from a large reservoir. The diameters of the nozzle and the pipe are given by ddnn = 25 mm and ddpp = 50 mm, respectively. If the distances are given by XX = 4.6 m and YY = 0.9 m, calculate: (i) The flow rate through the nozzle (ii) The pressure at points A and B
Length of Pipe 1 = 300 m Length of Pipe 2 = 240 m Length of Pipe 3 = 210 m Length of Pipe 4 = 450 m *Pipe 2 and Pipe 3 are parallel Diameter of Pipe 1 = 200 mm Diameter of Pipe 2 = 150 mm Diameter of Pipe 4 = 250 mm discharge of the pipe system = 45 Liters/second Total hf = 8 meters f= 0.02 What is the diameter of Pipe 3? (in mm)
Based on the layout of the water supply system, as show in Figure 1, flow through the delivery pipe, Q = 2.50 cfs and diameter of the pipe, D = 2.65 inch with e = 0.015 inch. Ingore the minor pressure losses and use the following formulae to calculate the major pressure losses. The velocity of flow through the pipe and the friction factor, f, range are estimated to be nearly. Use g = 62.4 lb/ft^3 for water and use Moody's diagram. Water temperature is 20°C (68°F).
Hydraulics 6. Determine the Reynolds number of a 0.40 cubic meter per second oil of Gs=0.80 and an absolute viscosity of 0.025 Pa.s thru a 450 mm diameter pipe.
1. What is the rate of flow of water if the actual inside diameter is 1.5 inches and the flow pressure is 2592 lb/ft2 ? 2. Find the static head where the pressure is equal to 33 psi. 3. Calculate the velocity of water running in a pipe having a velocity head of 0.8 feet.
Water travels through a circular pipe with a diameter of 400 mm and at a speed of 5 m/s. The inertial force created by the flow is: Question 9Answer a. 1000 kgs/m b. 1000000 kgs/m c. 100000 kgs/m d. 10000 kgs/m
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa Please answer with complete and detailed solutions. thank you. ASAP
All friction factor f = 0.02 All pipe lengths L = 250m Diameter of Pipe A = 400mm with Flow Rate at Pipe A = 500 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Refer to the illustration below
Given: 50 cm/sec 7.48 gallons/ 1ft^3 Solve: gallons/hr
EXAMPLE 10.1 The internal and external diameter of the impeller of a centrifugal pump are 300 mm and 600 mm respectively. The pump is running at 1000 r.p.m. The vane angles at inlet and outlet are 200 and 30 ° respectively. The water enters the impeller radially and the velocity of flow is constant. Determine the work done by the impeller per unit weight of water.