The results given in Table 1 were obtained in a particle size distribution test for soil sample received in the laboratory. Table 1 US Sieve No. Size Opening(mm) Weight Retained(g) 4 4.75 0 10 2.0 18.5 20 0.85 53.2 40 0.425 90.5 60 0.25 81.8 100 0.150 92.2 200 0.075 58.5 Pan - 26.5i. Determine the percentage passing each sieve and plot the particle size distribution curve. ii. How much fine-grained soils are in the sample ? iii. Determine the amount of gravel and sand in the sample ? iv. Determine D10, D30, and D60 from the grain-size distribution curve. v. Calculate the uniformity coefficient, Cu. vi. Calculate the coefficient of gradation, Cc. vii. Describe the gradation curve (eg poorly graded)

The results given in Table 1 were obtained in a particle size distribution test for soil sample received in the laboratory. Table 1 US Sieve No. Size Opening(mm) Weight Retained(g) 4 4.75 0 10 2.0 18.5 20 0.85 53.2 40 0.425 90.5 60 0.25 81.8 100 0.150 92.2 200 0.075 58.5 Pan - 26.5i. Determine the percentage passing each sieve and plot the particle size distribution curve. ii. How much fine-grained soils are in the sample ? iii. Determine the amount of gravel and sand in the sample ? iv. Determine D10, D30, and D60 from the grain-size distribution curve. v. Calculate the uniformity coefficient, Cu. vi. Calculate the coefficient of gradation, Cc. vii. Describe the gradation curve (eg poorly graded)

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter2: Origin Of Soil And Grain Size

Section: Chapter Questions

Problem 2.6P: Repeat Problem 2.4 with the following data. 2.4 The following are the results of a sieve analysis....

See similar textbooks

Similar questions

Repeat Problem 2.4 with the following data. 2.4 The following are the results of a sieve analysis. a. Determine the percent finer than each sieve and plot a grain-size distribution curve. b. Determine D10, D30, and D60 for each soil. c. Calculate the uniformity coefficient Cu. d. Calculate the coefficient of gradation Cc.
A hydrometer test has the following result: Gs = 2.65, temperature of water = 26 C, and L = 10.4 cm at 45 minutes after the start of sedimentation (see Figure 2.25). What is the diameter D of the smallest-size particles that have settled beyond the zone of measurement at that time (that is, t = 45 min)? Figure 2.25 ASTM 152H type of hydrometer placed inside the sedimentation cylinder (Courtesy of Khaled Sobhan, Florida Atlantic University, Boca Raton, Florida)
Repeat Problem 2.8 using the following data. 2.8 The following are the results of a sieve and hydrometer analysis. a. Draw the grain-size distribution curve. b. Determine the percentages of gravel, sand, silt and clay according to the MIT system. c. Repeat Part b according to the USDA system. d. Repeat Part b according to the AASHTO system.
Repeat Problem 2.14 with the following values: Gs = 2.75, temperature of water = 21C, t = 88 min, and L = 11.7 cm. 2.14 A hydrometer test has the following result: Gs = 2.65, temperature of water = 26 C, and L = 10.4 cm at 45 minutes after the start of sedimentation (see Figure 2.25). What is the diameter D of the smallest-size particles that have settled beyond the zone of measurement at that time (that is, t = 45 min)? Figure 2.25 ASTM 152H type of hydrometer placed inside the sedimentation cylinder (Courtesy of Khaled Sobhan, Florida Atlantic University, Boca Raton, Florida)
A liquid limit test performed on a soil sample has the following results, compute for the approximate value of the liquid limit. Round off your answer to two (2) decimal places. No. of blows = 20 Moisture content = 40.8%
A Sample of soil was tested in the laboratory with the following results Liquid limit =30% Plastic limit =12% U.S. Sieve Size Percentage Passing 3/8 in. 100.0 No. 4 76.5 No. 10 60.0 No. 40 39.7 No. 200 15.2 Classify the soil sample by the USCS classification system.
Calculate the CEC of a 100g soil sample that was found to contain the following cations: Ca2+ = 0.12g Mg2+ = 0.024g K+ = 0.078g Al3+ = 0.027g NH4+ = 0.036g H+ = 0.002g
Let us assume that a soil sample taken in the field is taken and it must be identified by the SUCS Method and AASHTO Method. Moisture content = 5.75% Limit liquid = 53.5 Plastic limit = 31.6 Granulometry Sieve % Pass No. 4 100 # 40 68 # 200 54.3 Do you select the best answer? a) Inorganic silt and sand, with low plasticity b) Inorganic clay with low plasticity c) Clay silt, traces of gravel, dark Brown
Given are the results from the liquid limit and plastic limit test for a soil sample. - Plastic Limit: PL = 18,7% Liquid Limit Test Number of Blows, N Moisture Content (%) 15 42 20 40.8 28 39.1 a) Draw the flow curve (to scale) and obtain the liquid limit of the soil sample. (5) b) Determine the plasticity index (PI) of the soil sample
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the liquidity index of this clay? (Use Interpolation) Group of answer choices 0.895 0.96 1.08 0.90 Please answer this asap. For upvote. Thanks
A liquid limit test performed on a soil sample has the following results, compute for the value of the flow index. No. of blows Moisture content 20 39.7% 30 37.6% Select one: a. 11.63 b. 11.93 c. 10.85 d. 10.67
Engineering statistics, i need solutions in 15 minutes please. MCQ/The table below shows the results from the specific gravity (S.G.) test performed in a soil laboratory including twenty samples of sand. Determine the Coefficient of Quartile Variation. A-0.011 B-0.033 C-0.024 D-0.087 E-0.065