: The rigid beam shown in figure is fixed to the top of the three rods. The two outer rods are aluminum [Ea=70 GPa] and the middle rod is steel [E 200 GPa]. After the load (P) is applied, the stress in steel rod is found to be (24.5 MPa). Determine: 4. The stress in aluminum rod. 5. The load (P). 6. The deformation of aluminum rod.

: The rigid beam shown in figure is fixed to the top of the three rods. The two outer rods are aluminum [Ea=70 GPa] and the middle rod is steel [E 200 GPa]. After the load (P) is applied, the stress in steel rod is found to be (24.5 MPa). Determine: 4. The stress in aluminum rod. 5. The load (P). 6. The deformation of aluminum rod.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.3P: The L-shaped arm ABCD shown in the figure lies in a vertical plane and pivots about a horizontal pin...

See similar textbooks

Similar questions

The round tapered brass bar, in Figure Q4, of length 500 mm is subjected to loads.Determine the change in length if E = 1×106kg/cm2
Figure Q3 shows a steel bar of diameter 16 mm and length 600 mm subjected to axial forces.If E = 210×103 N/mm2for steel, determine the change in its length.
2. The structure is connected by a pin joint at point A and by a cable of length L at points B and C, respectively.When load P is given at point D as shown below, what is the vertical displacement at point D?
The mechanism shown in the figure controls the lifter. Calculate the reactions on CDE as the weight supported by the platform is W W(N)= 2800, L1(m)=0.6, L2(m)=0.6 , L3(m)=0.2 1) For three dimensional problems, please use vector notation.2) State what all the transactions you have done. All intermediate actions you have to doshow clearly.3) Please write the units next to the values you find.4) In the related questions, please draw the free body diagram.
1. A force P = 27 kN acts on a round bar with d = 50 mm, find the stress in KPa. 2. The piston rod of a steam engine is 70mm in radius and 400 mm long. The radiusof the piston is 200mm and the maximum steam pressure is 2 N/mm2. Find thecompression of the piston rod if the young's modulus for the material of the pistonrod is 250 kN/mm2.
Figure Q2 shows few loadings applied on bar ABD. Suppose the diameter of the bar is 60mm,and knowing that P1 = 13kNm, P2 = 5 kNm and P3 = 12 kNm. Values A,B,C are given in TableQ2. (a) Find the following stresses at point H. (i) Normal stress due to P1 (ii) Bending stress and shear stress due to P2 (iii) Normal stress due to P (b) Determine the state of plane stress at point H and show it on the element. (c ) Using Mohr’s circle, determine the principal stresses at point H and show the result onthe element.
1. Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive load of 250 kN. The section dimensions are breadth, b = 0.12 m, depth, d = 0.05 m with an equal thickness on all sides, t = 0.003 m. Calculate the compressive stress σ in the tube. Give your answer in N/mm2 to 2 decimal places.
The bronze bar 2.72 m long with a cross-sectional area of 496 mm2 is placed between two rigid walls. At a temperature of 8.61 °C, there is a gap Δ = 2.28 mm, as shown in the figure. Find the compressive force (in N) experienced by the bar at a temperature of 61.85 °C. Use α = 18 × 10-6 /°C and E = 80.84 GPa. Round off your answer to three decimal places.
Figure Q2 shows the cross-section of a closed ended thick-walled cylinder with inner radius, ri, 0.1 mand outer radius, ro, 0.2 m. The cylinder is subjected to internal pressure, pi and external pressure, po.One of the design specifications is to maintain the hoop stress at the outer surface of the cylinder at zerovalue. If po = 50 MPa and by using Lame’s equations for thick-walled cylinder, (a) determine the value of pi to achieve the design specification (b) sketch the hoop, radial, and longitudinal stress variations across the wall thickness and label their values at the inner and outer radius of the cylinder (c) determine the absolute maximum shear stress existing in the cylinder wall material
Using this equation FL/AE The assembly consists of two rods (AB and CD) and a rigid bar (AC). A force of 6 kips is applied as shown in the figure. Let AAB = 1.5 in2, ACD = 1.1 in2, LA = 6 ft, LC = 4 ft, a = 1 ft, b = 2 ft and E= 17400 ksi. Determine the deformation in bar CD? Determine the deformation in bar AB? Determine the angle of rotation in rigid bar AC?
How many cables supporting the mass M ? mass (M) 400 kg as shown in the figure below. If a = 4 m, b = 5 m, c = 3 m, k1= 5000 N/mm and k2= 4000 N/mm.
A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. Suppose m = 2.0kg, L = .60m, M = 0.50kg, and angle(theta) = degrees. a. Using numbers, what is the magnitude of the tension force in the rope connecting the board and wall? b. Using numbers, what is the magnitude of the force applied by the hinge? c. Using numbers, in what direction does the force applied by the hinge point?