The roof truss as shown below is subjected by external loads exerts from the roof and purlins. Find the reactions of truss on its supports that will transfer to beams.

Q: Find the reactions at the supports for the beam that weighs 10 kN shown below. The length of the…

A:

Q: E Find the Reactions at pont A where the tensile force in cable CB is 300 KN. Neglect weight of AB.…

A: Consider the Free Body diagram:

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A * ?

A:

Q: A man raises a 10-kg joist with a length of 4 m by pulling on a rope.Find the tension T in the rope…

A: Given Data: The mass of the joist is M = 10 kg. The length of the joist is L = 4 m. The tension in…

Q: Find the Vertical and Horizontal Support Reaction at A

A:

Q: Compute the moment of area of the M diagram between the reactions about both the left and the right…

A:

Q: Find the reaction in pin A?

A:

Q: Find the reaction in pin A ?

A: Consider the free body diagram shown below for the given system.

Q: For the force at C, find the reactions at D, E, and A.

A: Solution: given dataF = 10 lb

Q: Calculate the reactions at supports A and B of the truss in the figure. Neglect the weight of the…

A:

Q: For the drawing shown find the reactions forces in (hinge A) and the force in (cable T)

A: Let Ax be the horizontal reaction at point A and Ay be the vertical reaction at point A. Under…

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A

A: Given data Forces acting are 2KN, 4KN/m

Q: A boom with an angle of theta, supports a 1000 lbs load as shown in the figure. Assume that the…

A: Givenweight W=1000lbsforce exerted by boom =3 times tension in rope

Q: 3. Find the reactions at the supports A and B for the beam given below. The length of the beam is…

A: This question is based on the concept of classical mechanics and strength of materials.

Q: The force in the truss AB

A: Given data; Trusses support load of =100 NLength of each truss is=1.0Cross-sectional area=200…

Q: Find the reactions at the supports for the beam that weighs 10 kN shown below. The length of the…

A:

Q: Q/Draw free body diagram then find reactions at pin support (O) and smooth surface (B) take beam OB…

A:

Q: • A sphere weighing 100 N is tied to a smooth wall by a string as shown in Figure. Find the tension…

A: Given: The weight of the sphere is W= 100 N. The free-body diagram is shown below, Here T is the…

Q: The frame below is used to support the distributed load as shown. 12) a) Find the reactions at C and…

A: Given data Given force system

Q: Compute for the reaction at A Compute for the reaction at D

A:

Q: For the given system below, find the reactions of the support at O

A:

Q: Find the reactions at the support A and B in the system below.

A:

Q: Find the reaction forces at A.

A: Consider the free body diagram of the beam as shown below.

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A and B

A:

Q: a uniform ladder 16 m long weighing 80 N leans against a smooth vertical wall, making 30 degree with…

A: Given details: L=16 mW=80 Nθ=30°

Q: A beam BC and a cable AB support a weight of 1200lbs. as shown below. The beam weighs 300 lbs.…

A:

Q: A and vertical pin reaction at D are respectively. Note: the reaction force at A E. and E have only…

A: Take equilibrium conditions (moment at any hinge is zero, summation of vertical force is zero) for…

Q: In the mechanism shown, find the force P and all reaction forces. Ignore weight forces and friction

A: Considering that the mechanism is in equilibrium with the action of the applied torque and external…

Q: Find the Reactions at point A where the tensile force in cable CB is 300 KN, 35 Neglect weight of…

A:

Q: Draw the F.B.D. for the beam shown in fig * ? and then find the reactions at A and B

A: Consider the free body diagram shown below for the given beam.

Q: A boom hinged at the base of a vertical mast is used to lift a 2000 load. Find the tension in the…

A:

Q: ind the reaction of both supports

A: Given: TO determine: Reaction supports

Q: The knotted cords in the figure is in equilibrium. Find the tension in each cord that supports a…

A: Given data: The magnitude of the weight, FW = 800 N. Draw a free-body diagram of the bottom knot.…

Q: The block system is stationary as shown in the figure. compute the internal reaction of horizontal…

A: Given  data Given force system.

Q: Determine the reactions at A and B shown in Figure below, neglect the weight of beam

A:

Q: Ecample The figure shows a laterally loaded beam which is supported by two rollers and in…

A: From the given information,

Q: The roof truss shown in the figure has fixed support at F and roller support at A. Find the reaction…

A:

Q: Q3 Find the reactions in supports 40N/m 4m إضافة ملف

A: Find the reaction at fixed support

Q: A beam has a pin support at A and a roller support at B. Given the load forces, find the support…

A: Given, The total length of the beam is 9 m.

Q: The length of a beam is nine meters. From the left end, it carries a triangular load of 300N/m.…

A:

Q: find the reactions at each support for the truss shown.

A: Given: To find reactions at each support

Q: Q4) Calculate the reactions at supports. 400 N/m 400 N /m

A: Given

Q: (a) Draw a FBD for the beam. (b) Find the tension in the cable. (c) What is the magnitude of the…

A:

Q: A plate with dimension of ( 5 ft x 8 ft) has uniform density andn its weight is 270 Ib. This plate…

A: From above FBD We get…

Q: Situation #4: A three-hinge arch is composed of two trusses hinged together at D. Find the…

A:

Q: equilibrium state of length (4 m) By A man raises a (to kg)) joist at L equilibrium state of length…

A:

Q: A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass…

A:

Q: Find the force constant of the spring. Assume that the angle that the ramp makes with the horizontal…

A: Given,       mass of the puck  m=0.18 Kg                           angle θ=22°…

Q: A uniform ladder, 4.8 m long and weighing 220 N, rests against a smooth vertical wall. By taking…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.