Please answer 3.2 only with reference to 3.1 Question 33.1.The 10 kg disk shown below is pin supported at its center. Determine thenumber of revolutions it must make to attain a speed of 150 rpm starting fromrest. It is acted upon by the constant force F = 10 N, which is applied to thecord wrapped around its periphery, and a constant couple moment T = 5 Nm.Neglect the mass of the cord in the calculations.T= 3 Nm.0.2 mF= 10N3.2.The same disk is suddenly unbalanced and its axis passing through its masscenter G. If it is released from rest, determine the horizontal and verticalcomponents of reaction at the pin O as shown below.1000,10 kg

Answered: Image /qna-images/answer/f5138350-95d2-406b-82fc-33cc4a9b327b.jpg

The same disk is suddenly unbalanced and its axis passing through its mass center G. If it is released from rest, determine the horizontal and vertical components of reaction at the pin O as shown below. 3.2. 100 G 0, 10 kg

The same disk is suddenly unbalanced and its axis passing through its mass center G. If it is released from rest, determine the horizontal and vertical components of reaction at the pin O as shown below. 3.2. 100 G 0, 10 kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A min cage of mass 4t is to be raised with an acceleration of 1.5m/s2 by a cable passing over a hoist drum of 1.5m diameter. What is the power required when the load has reached a velocity of 6m/s, neglecting the inertia of the drum and weight of the cable, but allowing for bearing friction torque of 3kN at the drum? What is the power required at a uniform velocity of 6m/s
Three 25-lb rotor disks are attached to a shaft that rotates at 720 rpm. Disk A is attached eccentrically so that its mass center is in. from the axis of rotation, while disks B and C are attached so that their mass centers coincide with the axis of rotation. Where should 2-lb weights be bolted to disks B and C to balance the system dynamically?
A drum A, of mass 200 kg, external diameter 380 mm and radius of gyration 150 mm, rotates on frictionless bearings at 250 rev/min. A stationary drum, B, of mass 50 kg, external diameter 200 mm and radius of gyration 80 mm, mounted on a frictionless axis parallel to that of A, is pressed into contact with A with a force of 90 N. The coefficient of friction is 0·25. Determine: The final speeds of A and B. (b) The time of slipping. (c) The time of slipping if a torque is applied to A, to maintain the speed of A as a constant 250 rev/min.
The arms of a Porter governor are 225 mm long. The upper and lower arms are pivoted to links of 35 mm and 45 mm respectively from the axis of rotation. Each ball has a mass of 4 kg and the sleeve mass is 35 kg. The force of friction on the sleeve of the mechanism is 44 N. Determine the range of speed of the governor for extreme radii of rotation of 115 mm and 145 mm.
Hey, please reply as soon as POSIBLE! Wheel A, of 30kg, is located in the position shown by the effect of idler wheel D (frictionless wheel) and the system rope-spring BC. The static coefficient of friction is 0.50 and the kinetic coefficient is 0.40 between all the contact surfaces. If the force exerted by the horizontal spring is 60 N: a) Determine whether or not wheel A is turning when a moment M of 60 Nm is applied at point G. b) If it is shown that under the previous condition the wheel is turning, calculate the new value of the moment M necessary for the wheel to keep turning in equilibrium. Also indicate the frictional force that is generated at point F under that condition.
In your job as a mechanical engineer you are designing aflywheel and clutch-plate system. DiskA is made of a lighter material than disk B, and the moment of inertia ofdisk A about the shaft is one-third that of disk B. The moment ofinertia of the shaft is negligible. With the clutch disconnected, A isbrought up to an angular speed v0; B is initially at rest. The acceleratingtorque is then removed from A, and A is coupled to B. (Ignorebearing friction.) The design specifications allow for a maximum of2400 J of thermal energy to be developed when the connection ismade. What can be the maximum value of the original kinetic energyof disk A so as not to exceedthe maximum allowed value of the thermalenergy?
A spool of mass 60 kg is supported on two rollers at A and B as shown in FigureQ1(c). Neglect the mass of the inelastic cable, friction and the mass of therollers at A and B. Knowing that a constant pulling force P is applied in order tounwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spoolis (604) mm, Appendix Ashows the examples of identifying the radius of gyration using student ID.(i) Determine the angular acceleration of the spool. (ii) Determine the pulling force P. (iii) Explain with calculation on ways to increase the acceleration of cablebeing pulled. [
Question 2 The speed of the pickup truck’s engine is controlled by the Porter governor with 4 arms of equal length, and pivot on the axis of rotation. Each ball has a mass of 4 kg and the mass of the central load on the sleeve is 20 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift, and 200 mm when the governor is at maximum speed. The initial angular speed of the engine’s crank is 14 rad/s, and it has reached a maximum speed at an acceleration of 0.4 rad/s2 after 5 seconds.2(a). If the speed of the crank of an engine is equal to the speed of its governor, calculate the angle between the upper arm and axis of rotation (?) when the governor starts to lift and when it is at maximum speed. 2(b). Prove that the length of the governor’s arms is equal.
A loaded porter governor has four links each of 250mm long.two revolving masses each of 3kg and a central dead weight of mass 20kg .all the links are attached to respective sleeves at a distance of 40mm from the axis of rotation.the masses revolve at a radius of 150 mm at minimum speed and at a radius of 200mm at maximum speed , Determine the range of speed
A 10 kg , 0.5 m radius wheel is to rotate from rest to a speed of 100 rad/s in 5 s. Determine the tangential force ( N ) created at the rim of the wheel.
The 2.00-kg slender rod shown is hanging in a vertical position and is pin-supported at point A. The slender rod is initially at rest until a 1.000-kg block C, strikes it at its end at point B.The block slides on a frictionless surface with a velocity of 3.50 m/s to the right. After the impact, it slides with a velocity of 1.250 m/s to the right, and the bar rotates with an angular velocity, ω'. 1. What gives the correct kinematic relationship relating the final velocity of the center of the rod, v' , and its angular velocity, ω'? 2. What is the coefficient of restitution, e, between the block and the slender rod? 3. What is the magnitude of the horizontal impulse at the support at point A?
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.