The 7.9 kg frame AC and 4.2 kg uniform slender bar AB of length / slide with negligible friction along the fixed horizontal rod under the action of the 80 N force. Calculate the tenstion T in wire BC. the x-y plane is vertical.

The 7.9 kg frame AC and 4.2 kg uniform slender bar AB of length / slide with negligible friction along the fixed horizontal rod under the action of the 80 N force. Calculate the tenstion T in wire BC. the x-y plane is vertical.

Name: The 7.9 kg frame AC and 4.2 kg uniform slender bar AB of length / sli
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The 7.9 kg frame AC and 4.2 kg uniform slender bar AB of length / slide with negligible friction along the fixedhorizontal rod under the action of the 80 N force. Calculate the tenstion T in wire BC. the x-y plane is vertical.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.24P: A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The...

See similar textbooks

Similar questions

Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
A spring with squared and ground ends has 16 active coils diameter of 6 mm and pitch of 10 mm . If spring rate is 85 KN/m , determine the solid force?
A uniform rod AB of mass 40 kg and length 10m rests with the end A on rough horizontal ground. The rod rests against a smooth peg C where AC = 8m. The rod is in limiting equilibrium at an angle of 15° to the horizontal. Please show working out Find:a) the magnitude of the reaction at Cb) the coefficient of friction between the rod and the ground.
A uniform slender rod of mass m and length L is held in position by the smooth vertical wall and the hinge at O. The mass of the cylinder is m1 and all contacts (bearings) are ideal or frictionless. a. Determine the general expression for the normal force Na exerted by the wall on the bar.
Find the force P required to pull the 40-kg homogeneous roller with radius 720mm over the 90-mm curb.
A ladder of length 2L and mass M is positioned on level ground leaning against a wall such that the angle between the ladder and the horizontal is @. The coefficient of static friction between the ladder and the wall and between the ladder and the ground is jistatic = 0.66. The centre of mass ofthe ladder is halfway along it. For the ladder to be in mechanical equilibrium: Write down equations for the total r- and y-components of the 5 forces acting on the ladder
Include the FBD of the problem Can the system in given figure be in static equilibrium in the position shown? The uniform bar AB weighs 500 lb, and the weight of block C is 300 lb. Friction at A is negligible, and the coefficient of static friction is 0.4 at the other two contact surfaces.
Consider the system as shown below. The 45-kg disk rests on the surface for which thecoefficient of static friction is 0.2. Determine the largest moment M that can be applied to the barwithout causing motion. Mass of the bar BC is negligible. Joints B and C are frictionless hinges. Please solve the question
Can the system in given figure bein static equilibrium in the positionshown?The uniform bar AB weighs 500 lb,and the weight of block C is 300 lb.Friction at A is negligible, and thecoefficient of static friction is 0.4 atthe other two contact surfaces.
The figure below shows a cylinder, which is rotating in clockwise direction. A lever is pushing onto the cylinder, thus exerting a braking torque. The lever itself is loaded by a force FE . a) Draw the free-body diagram of the lever, determine the direction of the kinetic friction force.
the table lamp consists of two uniform arms, each weighing 4N, and a 10 N bulb fixture. if angle is 16 degrees calculate the couple CAthat must be supplied by the friction in joint A.
The uniform bar and the homogeneous cylinder each have a mass of 24 kg. The static coefficient of friction is μs at A, B, and C (the three points of contact). (a) Assuming equilibrium, calculate the normal and friction forces at A,B and C. (b) What is the smallest value of μs necessary for wquilibrium?