The sequence in Figure P2.2 represents a ball rolling into a wall and bouncing off of it. The ball is 10 mm in diameter. Make a graph showing the distance from the leading edge of the ball to the closest part of the wall (using the wall as the origin) as it changes from frame to frame.

Q: Question 2 continued. b) Figure Q2b shows a plane mechanism. Crank OA rotates at angular velocity of…

A: Please note that angular positions of link 2 and link 3 are not given so i calculated it using the…

Q: You are using a lightweight rope to pull a sled along level ground. The sled weighs 435 N, the…

A: W=435 N μk=.2  and θ=12°F=115 N Normal force (N) ∑Fy=0SoN+115sin12°-435=0N=411.09 N

Q: Figure Q3 (b) shows an input cylinder with a diameter 25.4 mm and an output cylinder with a diameter…

A:

Q: A centrifuge is often used for astronaut training. A simplified version is sketched in Figure P3-22,…

A: As the cockpit is rigidly fixed to the arm, there won't be any Coriolis component of acceleration…

Q: along the center line XX'. Q2A = 18 cm, AB = 72 cm.  1. With the crank in the position shown, draw…

A:

Q: For the non-offset slider crank shown in the figure below the crank O₂A is rotating at constant…

A:

Q: A pendulum in your house swings from one side to the other in a span of 0.8 seconds. How long is the…

A: Given data  Time is taken by pendulum to swing from one side to the other (t) = 0.8 s   To determine…

Q: In graphics draw the Unitary vectors that we use in curvilinear movements: a) In Polar coordinates…

A:

Q: A medium-size catapult launches a 4.5-kg steel sphere as in Figure Ql. The launch speed is given as…

A: Given that, Launch speed, vo=30 m/s,Launch angle, θ=35°,Launch position=2 m,Fence positio=49…

Q: A 5 in. diameter plunger is being pushed at 0.5 ft/s onto. tank filled with oil having a SG of 0.93.…

A:

Q: 5. An artificial satellite revolves around the earth with a relative velocity of 800 . If the…

A: Given: The relative velocity of the satellite is v=800 m/s. The acceleration due to gravity is g=9…

Q: What is the angular velocity in rad/s after one complete turn?

A:

Q: A particle P is projected from a point O on a horizontal plane and moves freely under gravity. Its…

A:

Q: A car weighing 500 kg moving with a speed of 10 m/s takes a turn around a circle with a radius of 25…

A:

Q: ttached is the image of the system, as well as the question. The equations are my derivations from…

A: From the given information, a.Total energy = Kinetic energy + potential energyPotential energy:P =…

Q: 2- Example: A bird flies east at 10m/sec for 100m. it then turns around and flies at 20m/sec for 15…

A:

Q: A rock is thrown horizontally off a 100 m high-rise building as shown in Figure Q4(a). It lands 95 m…

A: Given data,  Height of building is H= 100 m  Landed at distance of x= 95 m  Let acceleration due to…

Q: Figure Q3 above shows the schematic of a motor on the right pulling the mass on the left. It is…

A:

Q: please send handwritten solution Q4 part e

A:

Q: Figure Q3 above shows the schematic of a motor on the right pulling the mass on the left. It is…

A: (a) The uniform acceleration of the block can be determined as,

Q: (b) Explain what is wrong with the system shown in Figure Q4(b).

A: We all know that the refrigerator is a device who take a heat from low temperature and reject it to…

Q: In a baseball game, the ball hits the top of a wall that is 26 m high and located at 150m away from…

A: Given data as per question Wall height =26m  Angle = 300

Q: Q5) (a) Calculate the net force on the object of Figure 3. Give the magnitude of the net force and…

A:

Q: 1.)The velocity of the water at the entrance and exit of a pipe are 10 m/s and 3 m/s, respectively.…

A:

Q: (III) You are lying on a beach, your eyes 20 cm above the sand. Just as the Sun sets, fully…

A: Given data: *The initial height of the eyes from the sand is h1=20 cm=0.2 m. *The height of the eye…

Q: Steam engines are used in the generation of electrical energy, in an electrical power plant you want…

A: initial Internal energy of the fluid,u1 =800 kJheat loss during cooling, Q=-500 kJwork done on the…

Q: You are going to load a trailer similar to the one below with an aircraft engine that has a mass of…

A: Given data: Mass of the trailer, m1 = 117 kg. Mass of the aircraft engine, m2 = 1017 kg. Mass…

Q: Figure Q3 shows a circular surface centered at O having a radius of 20 cm. A bar PR slides along…

A: Given data: The radius of the circular surface, rOQ= 20 cm. The angle, Ɵ = 45O. The velocity at the…

Q: A tall, uniform, rectangular block sits on an inclined plane as shown in Figure [1]. If u_s = 0.4,…

A: Givenμs=0.4 let mass of block is 'm'

Q: A roundtable is at rest and then is set in motion with a constant angular acceleration 25 rad/s2.…

A:

Q: In Figure Q3 (a), a 27 gram bullet with velocity of 395 m/s is fired to the block in rest condition.…

A:

Q: You are working with an imagined cubical pot of water, 1 meter on each side, sitting on a stove.…

A: We are dealing with a calorimetry problem where a 1 g water mass  @ 99 Celsius is transferring heat…

Q: 2- Example: A bird flies east at 10m/sec for 100m. it then turns around and flies at 20m/sec for…

A: Answer: (a) The average speed is 16 m/s. (b) The average velocity is 8 m/s (towards west).

Q: please send handwritten solution Q4 part b

A:

Q: Figure Q3 above shows the schematic of a motor on the right pulling the mass on the left. It is…

A: Note: The mass of the block is assumed to be 150 kg, instead of 150 N. (a) The acceleration of the…

Q: Suppose that a 5-foot-long chandelier falls from a 35-foot ceiling and that you are 6 feet tall and…

A: Given Data: Length of the chandelier, L=5 ft

Q: Write the two equations of motion for mass #1 and mass #2 relating X1(s) and X2(s) to the force,…

A:

Q: After years of asking, you finally were allowed to go on a joy ride in your uncle’s 1956…

A: Given: After years of asking, you finally were allowed to go on a joy ride in your uncle’s 1956…

Q: Find the general solution of d³y d²y 6. 3D3 = 3-cos X dx3 dx2

A: Given

Q: Figure Q3 shows a circular surface centered at O having a radius of 20 cm. A bar PR slides along…

A: Consider the instantaneous diagram shown below for the given mechanism. Here, I is the…

Q: Suppose that a 5-foot-long chandelier falls from a 35-foot ceiling and that you are 6 feet tall and…

A:

Q: Analytically, determine the vertical height of the basket in Figure P5 when a = 24 in., b = 36 in.,…

A:

Q: The purpose of the gripper mechanism is to convert input power into the required motion and force to…

A:

Q: The planar two-link space-station assembly robot shown in Figure 1 consists of two identical links…

A:

Q: n sphere is supported by a pull p and a 200kn weight passing over a frictionless pulley. If a=30°.…

A:

Q: Explain what is wrong with the system shown in Figure Q4(b).

A: To find: The wrong in the system. Concept used: The process of taking heat from high temperature…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.