l Asiacell12:19 AM© 56% Oواجب بعد التغی یر.pdfQ1The single phase bridge half controlled rectifier with RL load &a freewheeling diode when firing angle is (90°).Draw the waveforms of (Vs, Ig, Vo, Is, IFD ) when the rectifierfeeding heavily inductive load & the circuit.Determine the rms value of freewheeling diode current when loadcurrent is level at (30A).Q2The single phase bridge inverter supplies from dc source a load ofresistance with inductance. The load voltage issquare wave.Determine the value of minimum & maximum load currents. Thesource voltage is (200V) & output frequency is (50HZ) .Theinductive load with (8 Q, 20 mH). Draw the waveforms of (V., I.)& the circuit.Q3The step-up chopper has input voltage of (400V) & output voltageof (800V). Determine the duty cycle of chopper .Draw the circuitof class E chopper.

Half wave rectifier-A half-wave rectifier is only passed one-half cycle of AC voltage waveform and…

The single phase bridge half controlled rectifier with RL load & a freewheeling diode when firing angle is (90°). Draw the waveforms of (Vs, Ig, Vo, Is, IFD ) when the rectifier feeding heavily inductive load & the circuit. Determine the rms value of freewheeling diode current when load current is level at (30A).

The single phase bridge half controlled rectifier with RL load & a freewheeling diode when firing angle is (90°). Draw the waveforms of (Vs, Ig, Vo, Is, IFD ) when the rectifier feeding heavily inductive load & the circuit. Determine the rms value of freewheeling diode current when load current is level at (30A).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1.-Find the Q point of both diodes, for the rectifier consider Silicon, n = 1, Also, Is = 1x10 -12 A. Consider for the circuit Ve = 30V, Rs = 330Ω, Vz = 12 V with Iz max = 45mA, Rx = 1.2kΩ.
4670V = VsR = 200kΩ C = 0.1μF Consider the circuit and parameters illustrated above. If a derating factor of 12% is sugested then calculate, 12) the maximum reverse voltage rating of the diodes; 13) the string efficiency of this arrangement; 14) the maximum difference in leakage current of the diodes; 15) the maximum difference in stored charge of the diodes.
A sinusoidal voltage of 48v, 60 Hz is applied to a half-wave rectifier with dynamic resistance of the diode of .001ohms turns ratio (3:1). Calculate the DC and RMS currents flowing through the load(R=210 ohms). Also calculate the dc output power developed, ac – input power supplied, rectification efficiency, and ripple factor.
Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.
01. AC system with rated voltage Vs=500kV, to be connected to a 6-pulse rectifier through a transformer with turn ratio r. The DC voltage Vd=250kV, DC current Id=1kA ,the converter equivalent reactance xd=35 ohm, and firing angle is 15⁰, find r=?. If the AC system voltage changes to 525kV or 475kV, what the r1 and r2 will be in order to keep the DC parameters unchanged? 02. The inverter of a 1000MW HVDC project is connected with a 400kV AC system with 120mH equivalent source inductance. Find the SCR. And to describe the strength of the system(strong, medium, weak, very weak?). If the reactive power is compensated by the connection of capacitors with 560MVA, find the ESCR.
A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the amplitude of the peak output voltage, Vpo appearing across the load., calculate the average DC voltage appearing across the load, calculate the DC current in mA drawn by the load.
Calculate the average value of the output DC voltage for 20 trigger angles (a = 20) for a three-phase full-wave controlled rectifier operating in a network with phase neutral voltage of 150V.
1- A testing transformer 220 V/100 kV (rms), 50 Hz is supplying a half wave rectifier circuit. If the load resistance is 5 MΩ, find: a- The value of the smoothing capacitor so that the time constant is 10 times the supply periodical time. b- The rated peak inverse voltage (PIV) of the rectifier. c- The number of series connected rectifiers if the rated PIV of a rectifier is 20 kV. d- The ripple and the output voltages.
2. Design a full wave rectifier for a regulator that delivers 100W electrical power to a white off-the-shelf LED. Per datasheet, the LED requires 33V and draws 3A current. You are required to limit the ripple voltage to less than 20% of average DC voltage of the output. Assume all diodes have Von=0.7V and negligible off current.a. Draw the circuit diagram.b. Determine the voltage of transformer and capacitance of the filter
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Calculate the average value of the output voltage for ? = 60 ° of a three-phase full-wave thyristor rectifier operating on a network with phase neutral voltage of 100V.