The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe and R= 3.4 kN, determine the principal stresses, principal planes, and the maximum shearing stress at point H. (Round the final answers to two decimal places.) C D 19 kN 120 mm 150 mm 120 mm E The principal stresses at point Hare MРа MPa The principal planes at point Hare Oa = Ob = The maximum shearing stress at point His MРа.

The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe and R= 3.4 kN, determine the principal stresses, principal planes, and the maximum shearing stress at point H. (Round the final answers to two decimal places.) C D 19 kN 120 mm 150 mm 120 mm E The principal stresses at point Hare MРа MPa The principal planes at point Hare Oa = Ob = The maximum shearing stress at point His MРа.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel pipe AB has a 102-mm outer diameter and a 6-mm wall thick-ness. Knowing that arm CD is rigidly attached to the pipe, determine the principal stresses and the maximum shearing stress at point K.
The cylindrical tank AB has an 8-in. inner diameter and a 0.32-in. wall thickness. Knowing that the pressure inside the tank is 600 psi, deter-mine the maximum normal stress and the maximum in-plane shearing stress at point K.Solve assuming that the 9-kip force applied at point D is directed vertically downwar
A 400-lb vertical force is applied at D to a gear attached to the solid 1-in. diameter shaft AB. Determine the principal stresses and the max-imum shearing stress at point H located as shown on top of the shaft
2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable axial stress of the puncher is limited to 101.85 MPa, determine the thickness (t) of the steel plate. The maximum shear stress of the steel plate is 50MPa.
9.3. The 3-in. diameter shaft is supported by a smooth thrust bearing at A and a smooth journalbearing at B. Determine the principal stresses and maximum in-plane shear stress at a point on theouter surface of the shaft at section a–a.
A 10-kN force and a 2.8-kN·m couple T are applied at the top of the 65-mm-diameter brass post shown. Determine the principal stresses and maximum shearing stress at point H. Determine the principal stresses and maximum shearing stress at point K.
The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8 ksi. If the outer diameter of the shaft is 2.5 in. and the engine delivers 200 hp to the shaft when it is turning at 1140 rev>min, determine the minimum required thickness of the shaft’s wall.
Two steel plates of uniform cross section A x B are welded together as shown. Knowingthat centric P (in kN) forces are applied to the welded plates with the angle β,determine:(a) the in-plane shearing stress parallel to the weld and the normal stressperpendicular to the weld .(b) Draw Mohr’s circle for the state of stress exhibiting the welded surface state A (90mm) , B (30mm) , β (20°) , P (130kN)
The 4.5-ft concrete post is reinforced with six steel bars, each with a 118-in. diameter. Knowing that Es5 29 3 106 psi and Ec5 4.2 3 106 psi, determine the normal stresses in the steel and in the concrete when a 350-kip axial centric force P is applied to the post
Show that the angle between the plane of the major principal stress and the plane of the maximum shear stress is 45° for any state of stress.
2) A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a 70-mm- long key. If a torque T=2.2kN·m is applied to the shaft, determine the width w if the allowable shearing stress in the key is 60MPa.
The storage tank shown contains liquefied propane under a pressure of 1.4 MPa at a temperature of 38 °C . Knowing that the tank has a diameter of 315 mm and a wall thickness of 2.8 mm determinethe maximum normal stress and the maximum shearing stress in the tank.