The steel roll shown has a mass of 1230 kg, a centroidal radius of gyration of 150 mm, and is lifted by two cables loopedaround its shaft.TATBABTATBAВ100 mmKnowing that for each cable TA= 3100 N and Tg= 3300 N, determine the acceleration of its mass center.m/s2 1.The acceleration of the mass center is

Answered: Image /qna-images/answer/6c062f8c-714b-401b-92a0-23b125af3cca.jpg

The steel roll shown has a mass of 1230 kg, a centroidal radius of gyration of 150 mm, and is lifted by two cables looped around its shaft. TA TB A TA TB A В 100 mm Knowing that for each cable TA= 3100 N and TR= 330O N, determine the acceleration of its mass center. The acceleration of the mass center is |m/s2 ↑.

The steel roll shown has a mass of 1230 kg, a centroidal radius of gyration of 150 mm, and is lifted by two cables looped around its shaft. TA TB A TA TB A В 100 mm Knowing that for each cable TA= 3100 N and TR= 330O N, determine the acceleration of its mass center. The acceleration of the mass center is |m/s2 ↑.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6/40 If the frictional moment at the pivot O is 2 N+m, de- termine the angular acceleration of the grooved drum, which has a mass of 8 kg and a radius of gyra- tion kg = 225 mm. 200 mm kg 12kg
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
The circular disk of 145-mm radius has a mass of 38 kg with centroidal radius of gyration k bar = 25 mm and has a concentric circular groove of 55-mm radius cut into it. A steady force Tis applied at an angle theta to a cord wrapped around the groove as shown. If T = 40 N, theta = 0, mu_s = 0.11, and mu_k = 0.09, determine the angular acceleration a of the
3) The force F, is applied to a rope which wraps around a hip with a radius of 200 mm. The disk has a mass of 30 kg. The disk moves in a vertical plane and has a radius of gyration of mass of 0.5 m with respect to a horizontal axis through the mass centre perpendicular to the plane of motion. The magnitude of the force F, in newtons is given by the ex- pression F, = 100+ 30^2, where t is in seconds. The sys- tem is released from rest when t is zero. When t = 4 s, determine(a) The angular velocity of the disk.(b) The velocity of point A on the rope.
The uniform slender bar of mass m and total length L is released from rest in the position shown. Determine the force supported by the small roller at A and the acceleration of roller A along the smooth guide, Evaluate your results for theta = 15 degree. Answer: NA= 0.228mg aA=0.113g
Dynamics For the system given, the bar AB has an angularvelocity of wAB = 4 rad/s. By use of vectornotation, determine the velocity of mass C, andthe angular velocity of bar BC when teta = 30°
a) Body A weighs 60 lb, has a radius of gyration with respect to a horizontal axis through G of 0.60 ft, and rolls without slipping along the inclined plane. The velocity of B changes from 15 to 6 fps (both upward) after moving upward a distance of 6 ft. Determine the weight of B using Newton's Equations of Mo- tion b) Solve question using the principle of Work & Energy. Which method is easier?
A stepped cylinder has the dimensions R₁ = 0.30 m, R₂ = 0.65 m, and the radius of gyration, k, is 0.35 m. The mass of the stepped cylinder is 100 kg. Weights A and B are connected to the cylinder. If weight B has a mass of 80 kg, and weight A has a mass of 50 kg, how far does A move in 5 seconds? In which direction does it move? (Draw all FBDs)
The 100-kgkg spool is resting on the inclined surface for which the coefficient of kinetic friction is μkμkmu = 0.1. The radius of gyration about the mass center is kGkGk_G = 0.26 mm. Determine the angular velocity of the spool, measured clockwise, when ttt = 6 ss after it is released from rest.
The 153-kg wheel has a radius of gyration about its center of mass O of kO = 283 mm. If it rotates counterclockwise at an angular speed of 1431 rev/min and the tension force applied to the braking band at A is TA = 1771N,a) Determine the angular acceleration, in rad/s2, so that the wheel comes to rest in 67.6 revolutions after TA and TB are applied.
A cable is wrapped around the spool’s center hub. The mass of the spool is m= 100 kg, the radius r1 = 0.4 m, r2 =0.6 m, and the radius of gyration is kG = 0.3 m. A horizontal force P = 10 N is applied to the cord. The spool is initially at rest and rolls without slipping. (2) The mass moment of inertia about point A _______(kg·m2)(two decimal places)