The steel shaft has four gears with corresponding number of powers as shown. The allowable shear stress is equal to 80 MPa, while the relative angle of twist in between gears is not to exceed 0.06 rad. Determine the required minimum diameter of the shaft if it rotates at 10 Hz and the gears are spaced 0.6 m. Use G = 75 GPa.

The steel shaft has four gears with corresponding number of powers as shown. The allowable shear stress is equal to 80 MPa, while the relative angle of twist in between gears is not to exceed 0.06 rad. Determine the required minimum diameter of the shaft if it rotates at 10 Hz and the gears are spaced 0.6 m. Use G = 75 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft is subjected to a distributed torque along its length of t = (10x2) N # m>m, where x is in meters. If the maximum stress in the shaft is to remain constant at 80 MPa, determine the required variation of the radius c of the shaft for 0 ≤ x ≤ 3 m.
The solid steel shaft carries the torques Tl = 750 N • m and T2 = 1200 N • m.using Ll = 1.0 = 2.5 m and G = 83 GPa, determine the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 40
The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72 MPa. the shaft is operating at an angular velocity of 1700 rev/min. Take ci= 0.75 co. A) If the motor is to deliver a power of 25 kW, determine the required minimum outer diameter of the tubular shaft to the nearest mm. Express your answer in millimeters. B)Determine the required corresponding inner diameter of the tubular shaft to the nearest mm. Express your answer in millimeters
Motor A develops a power of 300 W and drives a pulley at 90 rpm. Determine the required diameters of the steel shafts that drive the pulleys A and B if the allowable shear stress is τ perm = 85 Mpa.
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70034763 Pa and angle of twist of 2.23ᴼ. Use G = 83000000000 Pafor the shaft, x = 2.3 m, and y = 1.89 m. Round off the final answer to two decimal places.Please help me, I only have 30 mins left. TY!
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
The gear motor can develop 1 10 hp when it turns at 80 rev>min. If the allowable shear stress for the shaft is tallow = 4 ksi, determine the smallest diameter of the shaft to the nearest 1 8 in. that can be used.
The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof 32 Hz. The gears at B and C take out 120 kW and180 kW, respectively. The lengths of the two parts ofthe shaft are L1 = 1.5 m and L2 = 0.9 m.Determine the required diameter d of the shaft ifthe allowable shear stress is 50 MPa, the allowableangle of twist between points A and C is 4.0°, andG = 75 GPa.
The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72 MPa. the shaft is operating at an angular velocity of 1700 rev/min. Take ci= 0.75 co. A) If the motor is to deliver a power of 25 kW, determine the required minimum outer diameter of the tubular shaft to the nearest mm. B)Determine the required corresponding inner diameter of the tubular shaft to the nearest mm.
The shaft is made of A992 steel with the allowable shear stress of tallow = 75 MPa. If gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively, determine the required minimum diameterd of the shaft to the nearest millimeter. Also, find the corresponding angle of twist of gear A relative to gear D. The shaft is rotating at 600 rpm.
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.