The stepped rod shown in the figure is made of Al 2014-T6 aluminum alloy. At temperature T1 = 20°C, there is a gap of 0.2 mm between point A and the rigid wall. If the temperature is increased to T2-50°C and an axial compressive force of P= 20 kN is applied at point B, determine the support reactions at points A and C. Ay 80 mm B C A 20 kN 120 mm 400 mm 600 mm

The stepped rod shown in the figure is made of Al 2014-T6 aluminum alloy. At temperature T1 = 20°C, there is a gap of 0.2 mm between point A and the rigid wall. If the temperature is increased to T2-50°C and an axial compressive force of P= 20 kN is applied at point B, determine the support reactions at points A and C. Ay 80 mm B C A 20 kN 120 mm 400 mm 600 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.12P: A copper bar with a square cross section is inserted into a square rigid tube as shown in the...

See similar textbooks

Similar questions

An A-36-steel hoop has an inner diameter of 23.99 in., a thickness of 0.25 in., and a width of 1 in. If it and the 24-in.-diameter A rigid cylinder has a temperature of 65° F, determine the temperature to which the hoop should be heated in order for it to just slip over the cylinder. What is the pressure the hoop exerts on the cylinder, and the tensile stress in the ring when it cools back down to 65° F?
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 100 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure.
Two rods are connected to each other and are restrained at top and bottom. The top portion is steel with modulus of elasticity equal to 200x10^3 MPa and coefficient of thermal expansion equal to 11.7x10^-6/C, the bottom is made up of brass with modulus of elasticity equal to 105x10^3 MPa coefficient of thermal expansion equal to 20.9x10^-6/"C. The temperaturé rose to 50°C from normal condition introducing stresses in the bar. Determine the force induced in the bar. Note: Final Answer in 4 decimal places.
The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is Your answer The angle of twist between C and B is Your answer The reaction at point A is
The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 x 10-³. If Esteet = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.
The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w = 60 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported by the structure.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
The wire BC has a diameter of 3.4 mm and the material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle at D if the pull at the grip is slowly increased and reaches a magnitude of (a) P = 2250 N, (b) P = 3000 N.
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.1250 in. The average shear stress in the pin cannot exceed 50 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
A stepped circular bar having diameter 20 mm, 15 mm and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm, respectively, is subjected to an axial tensile force of 5 kN.If E = 100×103 N/mm2and Poisson’s ratio v = 1/m = 0.32 for the material of the bar, determine a) Total change in length.b) Change in each diameter.
The steel rod is shown in Figure has a diameter of 10 mm. It is fixed to the wall at A, and before it is loaded, there is a gap of 0.2 mm between the wall at B and the rod. Determine the reactions on the rod if it is subjected to an axial force of P = 20 kN. Neglect the size of the collar at C. Take Est = 200 GPa.
A copper bar with a square cross section is inserted into a square rigid tube as shown in the figure. The length of the copper bar is 1.2 m and the area of the cross section is 300 mm2. The bar is subjected to a force P that applies a uniformly distributed pressure to the copper. Calculate the force P if the longitudinal displacement of the bar is 2 mm. Assume that the modulus of elasticity of the bar is E = 110 GPa and Poisson’s ratio is v = 0.33. Disregard friction between the copper and the rigid tube.