The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at = 31.0.a= 5, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and r(magnitude only) at the point are S, = 26 MPa, S, = 45 MPa, and Sy = 26 MPa. Assume = tan-' this point on the inclined plane shown. Answers: MPa, r= MPа.

The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at = 31.0.a= 5, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and r(magnitude only) at the point are S, = 26 MPa, S, = 45 MPa, and Sy = 26 MPa. Assume = tan-' this point on the inclined plane shown. Answers: MPa, r= MPа.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 MPa, Sy = 29 MPa, and Sxy = 26 MPa. Assume β=tan^−1(b/a)=23.2∘, a = 7, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses σ (positive if tensile, negative if compressive) and ττ (magnitude only) at this point on the inclined plane shown.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 23.6 ksi, Sy = 2.8 ksi, and Sxy = 7 ksi. Assume β=19∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.
For soil elements shown in the figure, determine the maximum and minimum principal stresses. Also determine the normal and shear stresses on plane AB.
Using the equations for determination of stress at a point, calculate the value for the maximum shear stress that develops if the major principal stress is 7.2 ksi compression and the minor principal stress is 3.6 ksi tension.
For the beam shown below, b = 5 in and h = 12 in. If the beam is subjected to a transverse shear for of V = 8 kip, determine the largest shearing stress in the beam. Express your answer in psi to the nearest whole psi
The rigid beam BC shown in Figure is supported by rods (1) and (2) that have cross-sectional areas of 175 mm2 and 300 mm2, respectively. For a uniformly distributed load of w = 15 kN/m, determine the normal stress in each rod. Assume L = 3 m and a = 1.8 m. Please explain the solution
Show complete solution, include necessary figures. The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension.A. Draw the Mohr's circle for this stress combination.B. What is the maximum shear stress acting at the point and what value of normal stress acts on the plane?C. Determine the value of the normal and shear stress acting on a plane that is 30 degrees from the minor principal plane.
The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are Sx = 170 MPa, Sy = 85 MPa, and Sxy = 45 MPa, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 48°.
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 28 MPa, Sy = 28 MPa, and Sxy = 37 MPa. Assume β=tan−1(ba)=21.8∘β=tan-1(ba)=21.8∘, a = 5, and b = 2. Using the equilibrium equation approach, determine the normal and shear stresses σσ (positive if tensile, negative if compressive) and ττ (magnitude only) at this point on the inclined plane shown.