The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 65 MPa and S, = 230 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 47°. %3D Answer: Sn MPa Snt MPa %D

The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 65 MPa and S, = 230 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 47°. %3D Answer: Sn MPa Snt MPa %D

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Similar questions

The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
Q#2 Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and maximum in-plane shear stresses and also draw respective stress elements. Furthermore find out stresses on planes whose normal make an angle of 45 and 135 degress with x-axis. Show your results on stress elements (10 marks)
Determine the magnitude of the shear stress (in units of MPa) when the state of stress is oriented 45 degrees from the element shown (aligned with line AB).
state of plane stress at a point is represented by the stress element below: A. Draw the Mohr’s Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 50o clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr’s Circle with those obtained fro
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 245 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 53°.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 532 mm2 and P= 35.29 kN. Round off the final answer to four decimal places.
For soil elements shown in the figure, determine the maximum and minimum principal stresses. Also determine the normal and shear stresses on plane AB.
The supported beam in the figure has its cross section and area shown. Determine the Absolute Maximum Bending Stress, draw the stress distribution over the cross section at this location. Also, what is the stress at point C of the cross section?
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
The couple M is applied to a beam of the cross-section shown in a plane forming an angle β withthe vertical y-axis. Determine the total normal stress at point A, point B, point D.
In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa. Neglect the weight of the bar AB.