The structure in the sketch below consists of the two members ABC and CDE which are pin- connected at point C. The complete structure is supported by a weightless link at B and a fixed support at E. The link is perpendicular to part BCDE and pin-connected to the support at the bottom. The distributed loading acts perpendicular to the inclined part AB. The figure is not to scale. 600 N/ m A 900N 0.5 m D E C B 1.2m * 1m *- 1m - -1.3m- Calculate the support reactions that develop on the frame at points B and E.

The structure in the sketch below consists of the two members ABC and CDE which are pin- connected at point C. The complete structure is supported by a weightless link at B and a fixed support at E. The link is perpendicular to part BCDE and pin-connected to the support at the bottom. The distributed loading acts perpendicular to the inclined part AB. The figure is not to scale. 600 N/ m A 900N 0.5 m D E C B 1.2m * 1m *- 1m - -1.3m- Calculate the support reactions that develop on the frame at points B and E.

Name: The structure in the sketch below consists of the two members ABC and
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The structure in the sketch below consists of the two members ABC and CDE which are pin-connected at point C. The complete structure is supported by a weightless link at B and a fixed support at E.The link is perpendicular to part BCDE and pin-conne

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.1P: A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar...

See similar textbooks

Similar questions

A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar is subjected to a linearly varying distributed load with maximum intensity q0. Calculate the vertical deform at ion of the spring if the spring constant is 4 kips/in.
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
Determine the internal resultants FG, VG, and MG on the cross section at G of the horizontal frame member in Fig. P1.4-17. The uniformly distributed load on member AC has a magnitude w0=220 lb/ft. (See the inset for a definition of the resultants.)
The bar ABCD has rigid supports and consists of three prismatic solid segments, as shown. The end segments have cross-sectional area A1 = 840 mm2 and length L1 = 200 mm. The middle segment has cross-sectional area A2 =1260 mm2 and length L2= 250 mm. Loads PB and PC are equal to 25.5 kN and 17.0 kN, respectively. Determine the magnitude of the compressive axial force FBC (kN).
Consider the truss shown with a 125-lb load on point B. What is the magnitude and direction of the force exerted by the roller support on point E? A. 29.76 lb upwardsB. 95.24 lb upwardsC. 52.79 lb upwardsD. 0 lbE. none of the choices
The total axial load acting at the centroid at on the leftmost rib would be 2F2 and the total axial load acting at the centroid at section C would be 2F3 A) Assume that the axial member is in equilibrium and the applied forces are an unknown load F1, F2 = 11 kN , F3 = 9 kN , and F4 = 6 kN . Calculate the internal resultant normal force at section B. B) Calculate the internal resultant normal force at section D. C)Suppose the axial member has a circular cross section with a diameter of dB = 16 cm at section B and a diameter of dD = 8 cm at section D. What is the average normal stress in the section with the maximum magnitude stress?
Find the load on each bar of the cage given below. Its dimensions are base 2a and height 3a. EB passes through the midpoint of the lattice. Angle of force F1= 700 with horizontal (choose an angle between 15o and 75o)
For the truss given below, it is desired to determine the normal efforts that act on the members, so that, thus, possible constraints for its design are possible. Consider that at point A there is a second gender support; and at point D, a first-class support. As this is asked: what is the effort acting on bar AB? Is it guidance or assessment?Source: Hibbeler (2004, p. 588). HIBBELER, R. C. Resistance of Materials. 5. ed. Rio de Janeiro: Technical and Scientific Books Publisher, 2004. Question 1 options: a) A compression force of 100 kN acts on bar AB. B) A tensile effort of 100 kN acts on bar AB. c) A compressive force of 141.42 kN acts on bar AB. d) A compression force of 200 kN acts on bar AB. e) A tensile effort of 141.42 kN acts on bar AB.
A straight girder of uniform section and length L rests on supports at the ends, and is propped up by a third support in the middle. The weight of the girder and its load is w per unit length. If the central support does not yield, prove that it takes a load equal to (5/8)wL. ANSWER: 1.80cm and 2.48cm Please show solution to the answer.
The bank in the figure is considered to be a person sitting and the force exerted on the board is given as 300 N. The elasticity module of the boards that make up the bench E = 7 GPa, Calculate the collapse at the point where a person sits, since the width of a board is 150 mm and the height is 30 mm. (Hint: Consider the AB board as if it is built into points A and B.)