The T section shown in Fig. is the cross-section of a beam formed by joining two rectangular pieces of wood together. The beam is subjected to a maximum shearing force of 60 kN. Show that the NA is 34 mm from the top and the INA = 10.57 x 106 mm². Using these values, determine the shearing stress (a) at the neutral axis and (b) at the junction between the two pieces of wood. 200 mm

The T section shown in Fig. is the cross-section of a beam formed by joining two rectangular pieces of wood together. The beam is subjected to a maximum shearing force of 60 kN. Show that the NA is 34 mm from the top and the INA = 10.57 x 106 mm². Using these values, determine the shearing stress (a) at the neutral axis and (b) at the junction between the two pieces of wood. 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
From the given figure below and its properties, calculate the stress at the top where the maximum moment is located. (MPa) Properties: Beam width = 207 mmBeam height = 386 mmWLL = 12.48 kN/mWDL = 15.26 kN/mSpan of the beam = 8 mPrestressing force = 293 kNeccentricity = 135 mm
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
A hollow shaft shown with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 75 kN and torques TB = 16 kN-m and TC = 7 kN-m. 14. Calculate the polar moment of inertia of the section in mm4.1 15. Calculate the absolute value of the internal torque at H in kN.m. 16. Calculate the torsional shear stress at H in MPa. 17. Calculate the absolute value of the minor principal stress at point H in MPa. 18. Calculate the absolute value of the major principal stress at point H in MPa. 19. Calculate the absolute value of the maximum shear stress at point H in MPa. 20. Calculate the orientation of the principal axes in degrees. Kindly answer all numbers with complete solution
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1531 N, T = 4945 Nm, a = 0.87 m, b = 1.05 m, c = 0.77 m, w = 32 mm, and h = 77 mm .
For the beam in question 1, determine the maximum bending and shear stressesat point C, at point P of the section. Represent the stress cube
For the beam shown in the figure, find the shear stress at a point 30 mm above the bottom of the beam at section C.
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
Considering the fully restrained beam shown in Figure 2 where E = 200 GPa and I = 2x10^9 mm^4 If P = 70 kN, M = 100 kNm, L = 12 m., and G = 40 degrees. Use either the virtual work method or the method of consistent deformation and state what you use with a complete solution. thank you. 1. Determine the maximum positive and negative shear that is acting on the beam. 2. Determine the maximum positive and negative moment that is acting on the beam 3. Determine the maximum deflection of the beam. 4. If the maximum deflection is limited to 10mm, determine the diameter of the circular beam required.
Proposed exercise N ° 01 Find the angle of torsion of the free end with respect to the fixed end of the system in the figure. The material is steel and the dimensions are in cm. Proposed exercise N ° 2 Find the length that a hollow steel bar of D = 1.5cm and d = 0.5cm in diameters must have for its ends to rotate 30 ° relative to each other. An allowable shear stress of 713.8 kg / cm2 must not be exceeded, and G = 8.1573x105 kg / cm2