The temperature limits of a CO2 refrigerating plants are 25°C and -10°C. If the vapour is dry at the end of compression, calculate COP, the capacity of the refrigeration plant, if 4 kg/min fluid is circulated in the system. Use the following CO2 table. Also, draw the p-h and T-s diagram Temp Liquid Liquid entropy Vapour entropy Vapour enthalpy Latent in °C enthalpy enthalpy Sf in kJ/kg K Sg in kJ/kg K h; in kJ/kg hig in kJ/kg h, in kJ/kg 25 81.3 121.4 202.6 0.251 0.63 |-10 |-7.54 245.3 237 -0.042 0.84

The temperature limits of a CO2 refrigerating plants are 25°C and -10°C. If the vapour is dry at the end of compression, calculate COP, the capacity of the refrigeration plant, if 4 kg/min fluid is circulated in the system. Use the following CO2 table. Also, draw the p-h and T-s diagram Temp Liquid Liquid entropy Vapour entropy Vapour enthalpy Latent in °C enthalpy enthalpy Sf in kJ/kg K Sg in kJ/kg K h; in kJ/kg hig in kJ/kg h, in kJ/kg 25 81.3 121.4 202.6 0.251 0.63 |-10 |-7.54 245.3 237 -0.042 0.84

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refrigerant -134 a enters the evaporator of a refrigerator as saturated vapor at −20∘ C and leaves at −10∘ C and 100 kPa. The volumetric flow rate at the inlet is 0.25 m 3/s Calculate the mass flow rate.
The air conditions at the intake of an air compressor are 28oC DB, 50% RH, and 101.325 kPa. The air is compressed to 400 kPa, then sent to an intercooler. If condensation of water vapour from the compressed air is to be prevented, what is the minimum temperature to which the air can be cooled in the intercoolers?
I need help on the following question: The vapour compression cycle (picture provided), utilises the refrigerant R134a flowing at 0.05 kg s-1. Assuming that the compression is adiabatic and reversible. If the actual input power to the compressor is 2 kW, then: 1. You need to determine the theoretical input power to the compressor and the heat transfer (Φ) to theevaporator. Take the enthalpies h1, h2, and h3 to be 238.41, 263.68 and 81.5 kJ kg-1 (use the 'NH3 Refrigeration Table' where you can find online). 2. You need to determine the coefficient of performance based on your answer to the previous question (1). 3. You need to determine the compressors mechanical efficiency.
Please Help,will provide helpful e Ratings for correct solution. Thank You. Water flows through a horizontal coil through which high-temperature flue gas passes. As water passes through the coil, it passes from the liquid phase at 200 kPa and 80°C to the vapor phase at 100 kPa and 125°C. The entry speed of water into the coil is 3 m/s and the exit speed of steam is 200 m/s. Calculate the heat transferred per unit mass of water through the coil? The enthalpies of the inlet and outlet streams are given as 334.9 kJ/kg and 2726.5 kJ/kg, respectively.
Define the Reversible Isothermal Compression
A saturated steam at 400kPa enters the turbine and exits as saturated liquid at 80o C flowing at 0.2m/s. If both inlet and outlet pipes have a diameter of 12.5cm, calculate the work produced in the operation. Perform Degree of Freedom analysis.
A three-stage compressor receives 500 lps of air at 101 kPaa and 27 oC, anddischarges at 750 kPaa. Determine a) the power required; b) the pressure at eachintercooler; c) the maximum temperature; and d) the heat transferred in each intercooler.e) What is the discharge temperature of a single-stage compressor operating at the same intake and discharge temperatures?(answers for Letter D and E Thank you)
PROBLEM: A flashed-steam geothermal power plant is located where underground hot water is available as saturated liquid at 715 kPa, The well head pressure is 680 kPa. The flashed steam enters a turbine at 635 kPa and expands to 15 kPa, when it is condensed. The flow rate from the well is 35.3 kg/s. Determine: Draw the T-S diagram The mass flow rate of steam in kg/s The power produce in KW The cooling water flow in kg/s if water is available at 25 oC and a 15°C rise is allowed through the condenser.
An aircraft is flying at a cruising speed of 250 m/s at an altitude of 5000 m where the atmospheric pressure is 54.05 kPa and the ambient air temperature is 255.7 K. The ambient air is first decelerated in a diffuser before it enters the compressor. Approximating both the diffuser and the compressor to be isentropic, determine (a) the stagnation pressure at the compressor inlet and (b) the required compressor work per unit mass if the stagnation pressure ratio of the compressor is 8.
What if the turbine and feed pump are not isentropic what would be the actual specific enthalpy and actual specific entropy and the actual temperature of the refrigerant at the exit of the feed pump, and the exit of the turbine/expander.
Water Vapor pressure 8 MPa and 350 in an adiabatic turbineIt enters at a temperature of oC and at a pressure of 750 kPacomes out. Reversible The amount of work done by the unit mass of steam for the processcalculate.
A flashed-steam geothermal power plant is located where underground hot water is available as saturated liquid at 725 kPa, The well head pressure is 670 kPa. The flashed steam enters a turbine at 645 kPa and expands to 15 kPa, when it is condensed. The flow rate from the well is 33.3 kg/s. Determine: Draw the T-S diagram The mass flow rate of steam in kg/s The power produce in KW The cooling water flow in kg/s if water is available at 25 oC and a 15°C rise is allowed through the condenser.