5.The three bars are pinned together and subjectedto the load P. If each bar has a cross-sectional area A, lengthL, and is made from an elastic perfectly plastic material, forwhich the yield stress is oy, determine the largest load(ultimate load) that can be supported by the bars, i.e., theload P that causes all the bars to yield. Also, what is thehorizontal displacement of point A when the load reachesits ultimate value? The modulus of elasticity is E.

Name: 5.The three bars are pinned together and subjectedto the load P. If e
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 5.The three bars are pinned together and subjectedto the load P. If each bar has a cross-sectional area A, lengthL, and is made from an elastic perfectly plastic material, forwhich the yield stress is oy, determine the largest load(ultimate load) th

Answered: Image /qna-images/answer/66eb2271-86ba-4e7c-b5fd-a2c8bcf2920c.jpg

Engineering

Mechanical Engineering

The three bars are pinned together and subjected ad P. If each bar has a cross-sectional area A, length smade from an elastic perfectly plastic material, for ne yield stress is oy, determine the largest load e load) that can be supported by the bars, i.e., the hat causes all the bars to yield. Also, what is the al displacement of point A when the load reaches ate value? The modulus of elasticity is E.

The three bars are pinned together and subjected ad P. If each bar has a cross-sectional area A, length smade from an elastic perfectly plastic material, for ne yield stress is oy, determine the largest load e load) that can be supported by the bars, i.e., the hat causes all the bars to yield. Also, what is the al displacement of point A when the load reaches ate value? The modulus of elasticity is E.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.63P: The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly...

See similar textbooks

Similar questions

A six-pack is shaken so that the pressurein each can is p = 20 psi. A board is placed onthe six pack and a student(s) weighing Wstands on the board so his weight is evenlydistributed to the six cans. The aluminumproperties are E = 10,000 ksi, Sy = 35 ksi, andν = 0.33. Each can has an average radius ofR = 1.25 in., thickness t = 0.01 in., and lengthL = 4.50 in.(a) Determine the critical weight of thestudent, Wcr , so that a stress element on thesurface of the can is in a state of uniaxial stress.Assume that no support is provided by thecontained liquid and the cans do not fail bybuckling (being crushed). (b) Determine thestrain in the longitudinal direction of the candue to pressure p = 20 psi and force Wcr.(c) Determine the strain in the hoop directionof the can due to pressure p = 20 psi and forceWcr
A rigid beam of negligible mass is pinned at one end and suspended from two cables. The beam is initially in a horizontal position and second, and then the 400-lb load p is applied.a) Determine the stress in each cable.b) determine the vertical movement of the charge P
The triangular block below is subjected to the Loads P=1200 lb and 400 lb. If AB=8 in, and BC is 6in., resolve each load into components normal and tangential to AC.
a) Determine the tensile force T’ in the rope on the side connected to joint B: b) Determine the internal compressive normal force ƒBC in the tube BC: c) Determine the horizontal reaction force Rx and the vertical reaction force Ry in joint A: d) Determine the moment M of the center of bar AB: e) Determine the compressive stress σBC in the tube BC: f) Determine the critical load Pc for the tube BC: g) Which of the following statements about the tube BC is correct: A. The tube BC fails due to yielding B. The tube BC fails due to buckling C. The tube BC fails due to both yielding and buckling D. The tube BC is safe against both yielding and buckling h) Pin C has a diameter of 30 mm; calculate the shear stress τ of the pin C, when considering one cross-section for shear stress calculation:
The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. If the downward force P will produce a 50 mm vertical displacement at the free end of lever AC, determine the force P if G = 83 GPa.
The lap joint is fastened with four ¾-inch diameter rivets. ➢ a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➢ b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➢ c. what is the maximum value of the load P (kips) that can be applied to the joint?
The lap joint is fastened with four ¾-inch diameter rivets. a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. c. what is the maximum value of the load P (kips) that can be applied to the joint?
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown inFigure: Q 4(b). Assume flange at point B always remains straight. (i) Sketch free body diagram (FBD) of segment AB and BC.(ii) Determine the magnitude of the force P if tensile stress in rod AB is equal to magnitudeof compressive stress in rod BC.
The uniform 300-1b bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B and the 0.5-in. diameter cable CD. Find the stress in the cable. DRAW THE FREE BODY DIAGRAM.
The rigid bar ABC is suspended from three wires of the same material. The cross-sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P.
Determine the loads acting on pins A and D of the frame shown. On the other hand, if the pin at B can withstand a maximum shear force of 800 lb, determine the maximum distributed load that can be applied to member AB.