The three figures show the stress-strain diagram for three different metals, c, b, and a, if you know that the three shapes have the same scale, answer the questions? Stress a Stress o Stress o (a) Arrange thethree met als according to ductility c>b>a -r a> b>c-1 b>c> a - b> a>c - B- Declared .has the lowest elastic modulus E C- Metal . has the greatest tensile strength SU NS

The three figures show the stress-strain diagram for three different metals, c, b, and a, if you know that the three shapes have the same scale, answer the questions? Stress a Stress o Stress o (a) Arrange thethree met als according to ductility c>b>a -r a> b>c-1 b>c> a - b> a>c - B- Declared .has the lowest elastic modulus E C- Metal . has the greatest tensile strength SU NS

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.
1. In the nominal stress-strain diagram (Figure 1), write down the names and meanings of points 1, 2, 3, and 4.2. Explain how to find the 0.2% offset yield strength, and explain the% elongation and% reduction in cross-sectional area.3. After explaining the difference between the true stress/strain and the nominal stress/strain, show the true stress-strain diagram for the nominal stress-strain diagram (Figure 1) to correspond points 1, 2, 3, and 4.
Please match different stresses to the stress value corresponding to the different points on the Stree-strain diagram of a low carbon steel. Proportional Limit Ultimate Strength Tensile Yield Strength A. A B. B C. D
If we want to measure the stress of a flat non-uniform component, what should we pay attention to before the measurement?
Identify shortly the parts of the stress-strain. Briefly explain each part.
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
Determine the young's modulus of metal alloy having the following tensile stress - strain diagram
Please annotate the attached stress strain graph of 0.9% carbon steel to show the different phases. From the graph work out the following: 1) modulus of elasticity 2) tensile strength 3) the ductility in % elongation 4) yield strength at a strain offset of 0.002
consider the following stress-strain graph of a hypothetical metal with a cross-sectional area of 28.27 mm2.1.) What is the maximum load that the metal can sustain?2.) If the final cross-sectional area after the tensile test is 12.57 mm2, what is the true stress in MPa?
Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram.
In the case of plane stress, how can the plane-strain analysis be used?
information: "When performing a tensile test of a metal, these values were found for stress and strain. the yield strength (YS) is stress at 0.2% plastic strain" The task: A 5 meter long rod of this material is loaded axially with a stress of 244 MPa.i. How long is the rod under load?ii. Then the bar is relieved, how long is it now?