The timber beam shown has the cross section shown. The moment of inertia about the z axis is 1,184 in.“. If P= 6370 lb, determine the horizontal shear stress Ty acting at point H. 2 in. 3.25 in. 8 in. 48 in. 48 in. 36 in. 2 in. 2 in. 6 in. 2 in. 60.1 psi O 80.0 psi O 68.3 psi O 72.7 psi O 57.2 psi Attempts: 0 of 1 used Submit Answer Save for Later

The timber beam shown has the cross section shown. The moment of inertia about the z axis is 1,184 in.“. If P= 6370 lb, determine the horizontal shear stress Ty acting at point H. 2 in. 3.25 in. 8 in. 48 in. 48 in. 36 in. 2 in. 2 in. 6 in. 2 in. 60.1 psi O 80.0 psi O 68.3 psi O 72.7 psi O 57.2 psi Attempts: 0 of 1 used Submit Answer Save for Later

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
In the weight wall support system given below, the internal friction angle of the sand ground behind the wall is 35 degrees and the beta angle is 20 degrees, the friction angle between the wall and the ground is 10 degrees, and the angle of inclination with the horizontal on the ground side of the wall is 82 degrees. In addition to these, the natural unit weight of the floor behind the wall is 15 kN / m.. According to this information, in order for the active resultant force on the wall to be 248 kN / m, how many meters should the wall height be? For the correct answer, the margin of error will be considered as 0.5. please fast
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from the top of the beam on section 2.47 in to the right of B if P = 1042 lb, Q = 4278 lb, w = 1.1 in, L = 7.37 in, b = 3.82 in, and h = 0.73 in.
g.) What is the moment of inertia (I) about the neutral axis of the section? (in mm^4) h.)What is the first moment of an area (Q) about the neutral axis of the section? (in mm^3) i.)What is the maximum shearing stress (fv) of the beam? (in MPa)
Since the beam M in the figure is under the effect of simple bending moment, calculate the bending stress and shear stress values at the A, B and C points. h = 400mm b = 140mm and M = 150KNm
P = 49 kips Determine the normal and shearing stress at point a, b, and c
For the beam in question 1, determine the maximum bending and shear stressesat point C, at point P of the section. Represent the stress cube
Consider the overhang beam shown in (Figure 1). Suppose that P = 6 kN, M= 6 kN⋅m, w= 4 kN/m. Point D is located just to the left of the roller support at BB, where the couple moment acts. Follow the sign convention. Part A Determine the internal normal force at point D. Express your answer to three significant figures and include the appropriate units. Part B Determine the internal shear force at point D. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at point D. Express your answer to three significant figures and include the appropriate units. Part D Determine the internal normal force at point E. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at point E. Express your answer to three significant figures and include the appropriate units. Part F Determine the internal moment at point…
A simply supported beam has a concentrated load at midspan. If the beam properties are given below, what is the final stress at bottom of the beam section where the maximum moment is located and the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 289 mmBeam height = 498 mmConcentrated load = 22.79 kNSpan of the beam = 9 mPrestressing force = 385 kNeccentricity = 123 mm
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
Consider a 130-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 55 kN-m and 60 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 165 mm, b2 = 40 mm, b3 = 290 mm, d1 = 65 mm, d2 = 240 mm, d3 = 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
Draw the shear force and bending moment diagram of the beam. Draw the distribution of normal stress and shear stress in the cross section of the beam at the B support. q(t/m)10 b(mm)60 h(mm)550 t(mm)40