The truck drives on a horizontal road with a constant velocity. It eventually bumped the wall due to reckless driving. In each of the following cases, the car stopped in the same amount of time. Which has the largest and smallest stopping force? M 3000 kg D 4000 kg O so00 kg 13 m/s 10 m/s 12 m/s E so00 kg X X 3000 kg U 4000 kg 10 m/s 15 m/s 12 m/s

The truck drives on a horizontal road with a constant velocity. It eventually bumped the wall due to reckless driving. In each of the following cases, the car stopped in the same amount of time. Which has the largest and smallest stopping force? M 3000 kg D 4000 kg O so00 kg 13 m/s 10 m/s 12 m/s E so00 kg X X 3000 kg U 4000 kg 10 m/s 15 m/s 12 m/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Ball A is thrown downwards at a velocity of 2.5m/s from a height of (h1=60m) while ball B is thrownupwards from a height of (h2=1.2 m) the two balls met at a height of (h3=25m) what is the initialvelocity of ball B
The open rail car is 6 ft. wide and filled with water to the level shown (FIGURE 8). When the car is moving with a constant acceleration of 10 ft/s2 26. How much water spills out of the car?a. 670.14 b. 139.86 c. 810 d. 562 27. What is the resulting pressure at point B?a. 561.6 b. 468 c. 212.8 d. 1123
A 1.5 m diameter open vessel, 2m high is filled with oil s.g= 0.85 at a depth of 1.6m and rotated at 47 rpm. a. what is the resulting depth of liquid at the center of the vessel? b. what angular speed should be imposed on the vessel such that the liquid touches the bottom surface of the vessel at the center? c. What angular speed should be imposed on the vessel such that there is no liquid 0.47m from the v ertical axis of the vessel?
A 450-N is in contact with a level plane of fk = 0.10. The block is acted upon by a horizontal force of 75N. The block reaches a velocity of 15m/s, starting from rest. If the 75-N force is then removed, how much longer will the block continue to move?
A concrete block with dimensions of H = 2 m, W = 2 m, and D = 0.2 m vertically placed on the ground. Supposethat you have a water gun to hit the block, and you are willing to overturn the block. If the concrete density is 2000kg/m3and the diameter of the jet is 50 mm, select three different vertical positions to hit the block and determine therequired velocities to overturn the block with a water gun.
A car is being towed up on an incline with an angle of 15ᵒ with the horizontal. Find the force (parallel to the incline) needed to pull the car with an acceleration of 1.2 m/s2. The car weighs 20 kN. Neglect friction. A. 5.18 kNB. 8.36 kNC. 2.45 kN D. 7.62 kN
Three large plates are separated by thin layers of ethylene glycol ( u = 1.61 x 10-2 Pa : s , p = 1.11329 ) and water , as shown in Figure . The top plate moves to the right at 2 m / s . At what speed and in what direction must the bottom plate be moved to hold the center plate stationary ?
A Block weighing 100N is held on a 400 incline by a Bar attached to a 150N Block on a horizontal plane. The Bar which is fastened by a smooth pin at each end is inclined 200 above the horizontal. The angle of Friction between each Block and its Plane is 180. Find the horizontal Force P applied to the150N Block which will cause it to be on the point of moving to the right?
1-Moment of inertia of the pulley (kg.m2) ? 2-tension in rope of m1 (N) ? 3-tension in rope of m2 (N) ? 4-angular acceleration of the pulley (rad/s2) ? 5-acceleration of block m1(m/s2) ? 6-acceleration of block m2 (m/s2) ?
If the block is 1000jg, determine the value of force P(N) that is causing the movement of the block usubstatic=0.50 and usubkinetic=0.35. A. 4700N B. 5000N C. 0 D. 4905N
Note: DRAW COMPLETE FREE BODY DIAGRAM WITH COMPUTED VALUES. Under the influence of a 700 N-m couple, the flywheel A revolves clockwise. A band break will be employed to bring A's rotation to a halt. The belt and the flywheel have a coefficient of friction of 0.40. a.) What is the minimal force required to stop the flywheel at the end of rod B? b.) What is the minimum braking force P if the 700 N-m couple acts counterclockwise on A?
A tanker contained with water is pushed horizontally at constant acceleration of 5.0 m/s?. If the tank is 10 m long and the depth of the water is 3 m when at rest, Calculate; a) The angle of water surface to the horizontal. b) The maximum pressure intensity on the bottom How far below the water surface should the top side of a vertical square 1 m on each side should be immersed so that the center of pressure will be 70 mm below the center of gravity? complete solution needed