The uniform rod (length 0.7 m) in figure rotates about an axis through one end, with a rotational inertia of 0.13 kg-m². As the rod swings through collides with a 0.20 kg stationary particle that sticks to the end of the rod. If the rod's angular speed just before collision is 2.5 rad/s, what is the am the rod-particle system immediately after collision? Rotation axis Rod Answer:

The uniform rod (length 0.7 m) in figure rotates about an axis through one end, with a rotational inertia of 0.13 kg-m². As the rod swings through collides with a 0.20 kg stationary particle that sticks to the end of the rod. If the rod's angular speed just before collision is 2.5 rad/s, what is the am the rod-particle system immediately after collision? Rotation axis Rod Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
5) In ice figure skating, a couple execute a “top” (see picture). The centre of mass of the woman (58 kg) is situated 1.3 m from the axis of rotation which is vertical and passes through the centre of mass of the man (85 kg). They are spinning at a constant angular velocity equal to 3.1415 rad/s and the man and woman have moments of inertia, about their own centres of mass, equal to 1.6 and 2.5 kg.m2 respectively. Then the woman grabs the neck of the man. At this point, her moment of inertia decreases to 1.4 kg.m2 and her body centre of gravity is 0.9 m from the axis of rotation. Determine the new angular velocity. Hints: This is a conservation of angular momentum problem, and needs the parallel axis theorem to determine moments of inertia about the axis of rotation. The skaters are moving as one body with one angular velocity, but they each have their own moments of inertia given relative to their own CoMs. For the man, that’s fine…the axis they’re rotating about passes through his…
A disk rotating with constant acceleration of 0.005 revolutions / s2 And the movement starts from rest. What is the angle velocity after one minute? How many turns makes the same disc in point number one after one minute. If an external force does not affect the body, what does that mean? And if the body is in free fall, is its speed constant or variable, what is its acceleration equal, and how can the friction be reduced between the contact surfaces
An object is formed by attaching a uniform, thin rod with a mass of mr = 6.86 kg and length L = 5.76 m to a uniform sphere with mass ms = 34.3 kg and radius R = 1.44 m. Note ms = 5mr and L = 4R. 1) What is the moment of inertia of the object about an axis at the left end of the rod? kg-m2 2) If the object is fixed at the left end of the rod, what is the angular acceleration if a force F = 463 N is exerted perpendicular to the rod at the center of the rod? rad/s2
Blocks A and B shown in the figure have masses of 5 kg and 10 kg respectively.If the pulley is treated as a 3 kg solid disk with a 15 cm radius, determine the acceleration of the block A. Disregard the rope mass and any slip on the pulley.Consider that the moment of inertia of the pulley is given by Ip = (1/2)mr² in which m is the mass of the pulley and r is of radius the pulley.
A plate weighing 400lbs, 3 ft tall and 6 ft wide is supported by two 6ft cables at its top left and right corners. The plate is put into motion creating a rocking motion. When the angle of the cables hits 60 degrees the tension in the cable is 40 lbs, what is the angular velocity of the plate?
(3) A pendulum consisting of a rod of mass 2m of mass 3kg and a ball of mass 1kg and a radius of 0.3m attached to one of the bar length. The axis of rotation as shown in the figure below What is the angular velocity of the pendulum at its lowest point if it is released from Rest at an angle of 30?
The radius of the flywheel given in the figure is 600 mm. Its mass is 144The radius of rotation (inertia) of the flywheel, which is kg, is 450 mm. to a mass of 18 kgObject A is suspended from a rope wrapped around the flywheel. system is stagnantbeing released in the (still) state. Object A 1.8 meters downFind the acceleration and velocity of the block when it moves straight.
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.
As seen in the figure, it has mass m1 and v isa bullet passes through a pendulum of mass m2 and its velocity v / 2exit with. Pendulum "L" long and mass negligibleIt is suspended on the end of a rope that can be carried. Your pendulum is a verticalminimum velocity v to move on the circlewhat should be min V?
A uniform rod (mass = 1.8 kg) is 1.5 m long. The rod is pivoted about a horizontal, frictionless pin through one end. The rod is released from rest in a horizontal position. What is the angular speed of the rod (in rad/s) when the rod makes an angle of 23° with the horizontal?. The moment of inertia of the rod about this axis is given by (1/3)ML2.
Suppose a 30 lb truck wheel 18 in. in diameter has a radius of gyration of 4 in. and the 6120 lb truck’s weight is distributed equally to each of the four wheels.a. If the truck can supply 150 lb x ft of torque to each wheel, how fast would the wheel want to accelerate if it didn’t slip? b. What would the coefficient of friction have to be in order to keep the wheel from slipping