QUESTION 4(a) With the aids of diagram, explain how gyroscopic moment is generated.(b) The thin disk of mass m kg and radius R shown in Figure Q4(b) rotates relative to the pivoted shaft ABof length L at constant angular speed . At the same instant, the entire assembly rotates at a constantangular speed of 2. Determine the relationship between the spin rate w and precession rate 2 so that theshaft AB is always in horizontal position (i.e. 0 = 90°)(c) Evaluate the angle 0 if the angular velocity of the disk is further increased?A32LFigure Q4(b)BJ

Answered: Image /qna-images/answer/dc1a8758-4734-4c4b-928b-f84c41a37be6.jpg

(a) With the aids of diagram, explain how gyroscopic moment is generate (b) The thin disk of mass m kg and radius R shown in Figure Q4(b) rota of length L at constant angular speed . At the same instant, the en angular speed of 22. Determine the relationship between the spin rate shaft AB is always in horizontal position (i.e. 0 = 90°) (c) Evaluate the angle 0 if the angular velocity of the disk is furt

(a) With the aids of diagram, explain how gyroscopic moment is generate (b) The thin disk of mass m kg and radius R shown in Figure Q4(b) rota of length L at constant angular speed . At the same instant, the en angular speed of 22. Determine the relationship between the spin rate shaft AB is always in horizontal position (i.e. 0 = 90°) (c) Evaluate the angle 0 if the angular velocity of the disk is furt

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The crankshaft of a vertical engine, stroke 250 mm, rotates at 300 rpm. The reciprocating parts have a mass of 100 kg. The connecting rod has a mass of 120 kg, it is 450 mm long, the C.G is 300 mm from the gudgeon pin axis and the radius of gyration about that axis is 363 mm. When the crank is 30o from the TDC position and moving downwards, find:-The total kinematic energy of the connecting rod
Derive the equations of motion of a slender rod with length of 1.2m mass of 10 kg is attached to a wheel of radius 0.1m mass of 2 kg. Horizontal external force, f, applied to the wheel axle, assume no slipping.
Q#03 : In a four-bar chain ABCD, Link AD is fixed and is 160 mm long. The crank AB is 40 mm long and rotates at 150+25 rpm clockwise. While Link CD is 70mm long and oscillates about point D. BC and AD are of equal length, angle BAD=60°. Find the angular velocity of Link CD? (Subject : mechanics of machines)
A flywheel connected to a punching machine has to supply energy of 400 Nm while running at a mean angular speed of 20 rad/s. If the total fluctuation of speed is not to exceed -2 to +2% What is the mass moment of inertia of the flywheel?
A uniform disk of radius 0.455 m and unknown mass is constrained to rotate about a perpendicular axis through its center. A ring with the same mass as the disk is attached around the disk's rim. A tangential force of 0.227 N applied at the rim causes an angular acceleration of 0.131 rad/s^2. Find the mass of the disk.
An object is formed by attaching a uniform, thin rod with a mass of mr = 6.86 kg and length L = 5.76 m to a uniform sphere with mass ms = 34.3 kg and radius R = 1.44 m. Note ms = 5mr and L = 4R. 1) What is the moment of inertia of the object about an axis at the left end of the rod? kg-m2 2) If the object is fixed at the left end of the rod, what is the angular acceleration if a force F = 463 N is exerted perpendicular to the rod at the center of the rod? rad/s2
An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at 200 km per hour. The rotary engine and the propeller of the plane has a mass of 400 kg with a radius of gyration of 300 mm. The engine runs at 2400 r.p.m. clockwise, when viewed from the rear. Find the gyroscopic couple on the aircraft and state its effect on it. What will be the effect, if the aeroplane turns to its right instead of to the left ?
A rotating disc of 2m diameter has two eccentric masses of 0.6kg each radii of 60mm and 70mm at angular positions of 00 and 1500, respectively. A balancing mass of 0.1 kg is to be used to balance the rotor. What is the radial position of the balancing mass?
Find the magnitude and position of the balancing mass at a radius of 13cm by using the analytical method. Three masses m1, m2, m3, are attached to a shaft and revolve in the same plane. The masses are 12kg, 10kg, and 15kg respectively and their radii of rotations are 5cm, 6cm, 7cm respectively. The angular position of the masses m2, m3 are 45° and 145° from the mass m1.
A flywheel of mass 0.9 ton is fitted to a multi cylinder engine, which runs at a mean speed of 380 r.p.m. If the speed varies from 9 % above the mean to 6 % below it and the fluctuation energy is 1100 kN-cm, find (i) mass moment of inertia of the wheel and (ii) radius of Gyration.
A thin square plate with dimensions of 0.65 m x 0.65 m and a mass of 5.00 kg is supported from pins at points A and B as shown in Figure 1.1 (Position 1).a. what's its moment of inertia about its center of mass?b. If the pin at point B is removed and the plate freely swings around pin A, what's the magnitude of theplate's angular velocity once it has rotated in a clockwise direction by 90° as shown in Figure 1.2 (Position 2)?c. what's the magnitude of the maximum angular velocity attained by the plate as it swings freely?(Hint: The maximum angular velocity will occur after rotating 45° clockwise upon release.)
A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating masses of the engine have an angular speed of 100 rad/s in clockwise direction when viewed from the front of the car The combined moment of inertia of the rotating masses is 10 kg-m².what is the magnitude of the gyroscopic moment in (N-m)?