Knowing thát the internal diameter of the HolUW SIlat shown is d= 23 mm, determine the maximum shear stress caused by a torque of magnitude T= 1.0 kNm. [Ans. 89.3 MPa] PROBLEM 3.4 Knowing that d= 30 mm, determine the torque T which causes a maximum shear stress of 52 MPa in the hollow shaft shown. Fig. P3.3 and P3.4 [Ans. 446.7 Nm] 40 mm

Knowing thát the internal diameter of the HolUW SIlat shown is d= 23 mm, determine the maximum shear stress caused by a torque of magnitude T= 1.0 kNm. [Ans. 89.3 MPa] PROBLEM 3.4 Knowing that d= 30 mm, determine the torque T which causes a maximum shear stress of 52 MPa in the hollow shaft shown. Fig. P3.3 and P3.4 [Ans. 446.7 Nm] 40 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the ends A and D of the two solid shafts AB and CD are fixed, while the ends B and C are connected to gears, as shown in the figure. Knowing that the maximum shear stress is 50 MPa in each axis, determine the maximum torque T that can be applied to gear B.
The composite shaft shown consists of a 0.2-in.-thick brass jacket (Gbrass= 5.6 × 106 psi) bonded to a 1.2-in.-diameter steel core (Gsteel=11.2 × 106 psi). Knowing that the shaft is being subjected to the torques shown, determine the largest angle through which it can be twisted if the following allowable stresses are not to be exceeded: τsteel=15 ksi and τbrass= 8 ksi.
A compound steel [G = 80 GPa] shaft consists of a solid 92-mm-diameter segment (1) and a solid 60-mm-diameter segment (2). The allowable shear stress of the steel is 96 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC ≤ 4°. Determine the magnitude of the largest torque TC that may be applied at C.
A steel shaft BCD (G=80 GPa) of total length 3 m is encased for 1/3 of its length by a bronze sleeve ABC (G=41 GPa) that is securely bonded to the steel. The diameter of the steel is 60 mm while the outer diameter of the bronze is 80 mm. a. What is the maximum allowable torque in gear A if the allowable shear stresses in the steel and bronze are limited to 110 MPa and 70 MPa, respectively; and the angle of twist between A and D is limited to 9o? b. What power is supplied by the motor that corresponds to the computed torque at A if shaft EF rotates at 200 rpm? The diameter of gear E is 60 mm while gear D has a diameter of 100 mm.
A steel pipe of 12-in. outer diameter is fabricated from 14-in.-thick plate by welding along a helix that forms an angle of 45° with a plane parallel to the axis of the pipe. Knowing that the maximum allowable tensile stress in the weld is 12 ksi, determine the largest torque that can be applied to the pipe.
A circular shaft AB consists of a 10-in.-long, 78-in.-diameter steel cylinder, in which a 5-in.-long, 58-in.-diameter cavity has been drilled from end B. The shaft is attached to fixed supports at both ends, and a 90 lb?ft torque is applied at its midsection . Determine the torque exerted on the shaft by each of the supports.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft with inner and outer diameters of 4 in. and 6 in., respectively. Knowing that the allowable shearing stress is 12 ksi, determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter.
A 1.5-m-long tubular steel shaft of 38-mm outer diameter d1 is to be made of a steel for which τall = 65 MPa and G = 77.2 GPa. Knowing that the angle of twist must not exceed 4° when the shaft is subjected to a torque of 540 N·m, determine the largest inner diameter d2 that can be specified in the design.
The driveshaft of an automobile is being designed to transmit 238 hp at 3790 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 5700 psi.
Q2: A solid steel shaft A of 60 mm diameter rotates at 300 rev/min. Find the greatest power that can be transmitted for a limiting shearing stress of 60 MN/m2 in the steel. It is proposed to replace A by a hollow shaft B, of the Same external diameter but with a limiting shearing stress of 75 MN/m2 . Determine the internal diameter of B to transmit the same power at the same speed.
A 1.5-m-long tubular steel shaft of 38-mm outer diameter d1 is to be made of a steel for which τall = 65 MPa and G = 77.2 GPa. Knowing that the angle of twist must not exceed 4° when the shaft is subjected to a torque of 660 N·m, determine the largest inner diameter d2 that can be specified in the design. The largest inner diameter d2 that can be specified is mm.