The viscosity of a fluid placed in the two cylinder ranges is given in the figure it is measured by device. Diameter of inner cylinder rotating at 300 rpm 20 cm and its height is given as 90 cm. The distance between the two cylinders is 1 mm. The moment applied to the rotating cylinder is measured as 2 Nm. find its dynamic viscosity. On the lower surface of the rotating cylinder friction is neglected. 300 rpm 1 mm Fluid Moving cylinder

The viscosity of a fluid placed in the two cylinder ranges is given in the figure it is measured by device. Diameter of inner cylinder rotating at 300 rpm 20 cm and its height is given as 90 cm. The distance between the two cylinders is 1 mm. The moment applied to the rotating cylinder is measured as 2 Nm. find its dynamic viscosity. On the lower surface of the rotating cylinder friction is neglected. 300 rpm 1 mm Fluid Moving cylinder

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 43 kg/s. Another identical elbow is attached to the existing elbow such that the water flow makes a U-turn as shown in the second figure. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. Take the density of water to be 1000 kg/m3.
Consider laminar flow of a Newtonian fluid in the y direction between two parallel andvertical plates with a distance between h, at steady state. The plate on the left isstationery and the other plate on right-hand side is moving vertically upwards at aconstant velocity Vo. Derive an equation for the velocity profile.
A wooden circular board 1m in diameter is being submerged vertically in a liquid having SG=1.15. Its topmost part is flushed in the liquid surface. Use 9.81kN/m3 as the specific weight of water. Find the: a) total hydrostatic force (kN) acting on one side of the board b) the distance (m) of the center of gravity from the liquid surface c) the location of the center of pressure measured from the liquid surface in meters Note: Do not round off intermediate values. Answer in four decimal places and do not include units in your answers.
3. A vertical piston-cylinder device on the left containing a gas has a mass of 40 kg and a cross-sectional area of 0.012 m². The local atmospheric pressure is 95 kPa, and the gravitational acceleration is 9.81 m/s². Determine the absolute pressure (kPa) inside the cylinder. (2 decimal)
A toy skyrocket consists of a solid conical top, ρi = 600 kg/m3, a hollow cylinder, ρc = 400 kg/m3, and a stick having a circular cross section, ρs = 300 kg/m3. Determine the length of the stick, x, so that the center ofgravity G of the skyrocket is located along line aa.
A closed tank contains compressed air and oil (SG = 0.90) as is shown in FIGURE FMVP-1. A U-tube manometer using mercury (SG = 13.6) is connected to the tank. The column heights are h1 = 36 in., h2 = 6 in, and h3 = 9 in. Determine the pressure reading of the gage in psi. a. 439.92 b. 5279.04 c. 3.055 d. 7132.32
FLUID MECHANICS: MOMENTUM EQUATION A cone that is held stable by a wire is free to move in the vertical direction and has a jet of water (at 10oC) striking it firm below. The cone weighs 30 N. The initial speed of the jet as it comes from the orifice is 15m/s, and the initial jet diameter is 2cm. Find the height to which the cone will rise and remain stationary. NOTE: The wire is only for stability and should not enter your calculations.
Civil meant Using a mass of 50 kg and a spring with a rigidity of 4 x 40 N/m, a vibrating system is viscously dampened. Two successive amplitudes have a 20:18 ratio. Find the undamped system's natural frequency. Calculate the damped natural frequency and damping ratio as well.
Based on the provided differential-type manometer, calculate the difference in the pressure between points A and B (as in Δp = pA - pB = ?). SG of oil is 0.8
The system in the figure is at 70°C (SG = 0.983). Determine the pressure at point C. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: Ib/ft?
Consider the following steady, two-dimensional, incompressible velocity field: V-› = (u, ?)= (−ax2) i-› + (2axy) j-›, where a is a constant. Calculate the pressure as a function of x and y.
Please answer. Thank you A 100- m steel tape is used to measure the distance of the line and found to be 1539.28 m long. During measurement, the tape is supported the ends under a pull of 10 kg and the observed mean temperature is 31 deg. celsius. The tape is of standard temperature of 20 deg. celsius and a tension of 12 kg. The cross sectional area of the tape is 0.035 sq. cm. The coefficient of linear expansion is 0.0000116/ deg. celsius and the modulus of elasticity of steel is 2.0 x 106kg/ sq. cm. The tape weighs 1.5kg. a) Determine the total correction for temperature. b) Determine the total correction due to sag. c) What is the correct length of the line?