Answered: The volume of air delivered by fan is…

The volume of air delivered by fan is 26 m^3/sec and 186 mm water gage. The density of air is 1.5 kg/m^3 and the motor power needed to drive the fan is 48 kW. Determine the fan efficiency in %

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.33P

See similar textbooks

Related questions

Q: A ventilating fan discharges 4.4 m3 of air per second through a duct 91cm in diameter against a…

Q: Water flows through a horizontal pipe at a rate of 2.4 gal/s. The pipe consists of two sections of…

A: Given data:Discharge of the water through a horizontal pipe is Q=2.4 gal/s Diameters of the…

Q: The total discharge in the system below is 15.5 cfs and the head loss from B to C is 24 ft. Using n…

A: Note: As per policy, we can solve the first three subparts. Please resubmit the remaining parts.…

Q: 2. A pump is used to move water (p = 1000 kg/m³) from a lake into a large tank as shown below. The…

Q: Oil is pumped from a very large tank (z1 = 150 m) to another tank (z2 = 200 m), located higher and…

Q: A horizontal water pipe diameter 15 cm converges to 7.5 cm diameter. If the pressures at the two…

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: Since you have asked multiple subparts, only the first three subparts are solved for you. If you…

Q: water flows through a horizontal venturyi meter whose inlet diameter is 33 cm. and throat diameter…

Q: A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to…

Q: (1) Q.2.A. Blood flows through the branching blood vessels as shown in figure at a rate of 1o lt…

Q: A fan draws 1.42 m° per second of air at a static pressure of 2.54 cm of water through a duct 300 mm…

Q: Water from a reservoir is pumped over a hill through a 450 mm diameter and an absolute pressure of…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: Two pipes, one of internal diameter (I.D.) 0.5 m and the other of I.D. 1 m, are connected as shown…

Q: At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is…

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: 2. In a pumping system handling water, the level in the suction tank is 3m below the pump shaft…

Q: When water is pumped into a water tank 20 m above a lake with a flow rate of 70 l/s, 20.4kW of…

A: Given data:- Head(H) = 20 m Discharge(Q) = 70 L/sec Electric power = 20.4 k

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft…

Q: Heavy oil is flows in a 40 cm diameter cast iron pipe f= 0.044. If the head loss due to pipe…

Q: Using the pump selection table below to determine the best pump for the given condition: • A flow of…

A: Option ( C ) is correct 100-80/20

Q: :Determine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3…

Q: Rank in order, from highest to lowest, the liquid heights h1 to h4 in tubes 1 to 4. The airflow is…

A: The height of liquid in tube increases with the increase in velocity, since higher the velocity,…

Q: Underground water is being pumped into a pool section 10 ft x 14 ft while water is discharged…

A: V2=Mean velocity =16.5 ft/secD2=diameter of orifice= 2 in=16 ftproperties of pool section=10 ft× 14…

Q: An orifice meter with orifice diameter 15 cm is inserted in a pipe of 30 cm diameter. The pressure…

A: The diameter of the orifice in the orifice meter is d=15 cm=15 cm×m100 cm=0.15 m. The diameter of…

Q: Determine the static fan efficiency if total fan mechanical efficiency is 70% and air is measured at…

A: Given DataQ=1.42m3/sηm=70%d2=275mmhw=2.54cmd1=300m

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft…

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost…

Q: Show in Figure 1 is the water flow system. The velocity head difference is = 2.0m. Volume flow rate…

A: Given data as per the question velocity head =2 m volume flow rate =0.5 m3/s h1 =1 m h2 =2 m hA = 3…

Q: 11. A pump discharges 280 kg/min of water whose specific weight is 920 kg/m3 (g = 9.765 m/s").…

Q: A fan draws 1.42 m³ per second of air at a static pressure of 2.54 cm of water through a duct 300 mm…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: (3) In the figure below, the pipe entrance is sharp-edged. Consider the flow rate Q to be 0.004…

Q: Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the…

A: When any fluid having velocity V passes through a pipe of area A, then discharge through the pipe is…

Q: A 6-cm-diameter horizontal water pipe expands gradually to a 9-cm-diameter pipe. The walls of the…

A: It is given Density of water = 1000 kg/m^3 Total inclined angle =60° If mass flow rate same We can…

Q: A square box with a length of 1.30 m contains water at room temperature. The box has two pipe…

Q: The water is flowing through a pipe having diameters 40 cm and 21 cm at sections land 2…

A: Given data D1 = 40 cm = 0.4 m D2 = 21 cm = 0.21 m volume flow rate (Q) = 45 litre/s = 45*10-3 m3/s…

Q: The power carried by fluid into the control volume, (W). Head carried by fluid out the control…

A: Total energy available at entry per unit volume is given by the the bernoulli's equation P₁ +…

Q: Q6. A pump moves water horizontally at a rate of 0.02m /s. Upstream of the pump where the pipe…

A: Given Data: Flow rate, Q=0.02 m3/s

Q: A 20 hp pump with a suction from an open reservoir (10 m above the pump) has a flow rate of 125…

Q: The weight of a water tank open to the atmosphere is balanced by a counterweight, as shown. There is…

A: Now as per the given condition The area of the outlet hole is given asAh=π4d2here d=4 cm=0.04…

Q: A pitot-static tube is used to measure the velocity of air flowing through a duct. The manometer…

A: A pitot tube is a mechanical device that is used to measure the velocity of flow at any point in the…

Q: The inlet and throat diameters of a horizontal venturimeter are 30 cm and 15 cm respectively. The…

Q: When a fan is operated at 1200 rpm the input power is 5 kW. If the speed is increased to 1300 rpm…

A: Power P=5 kWN1=1200 rpmN2=1300 rpmTotal pressure(h) =250 m of airρair=1.20 kg/m3So P=ρairgh…

Q: A pump shown in the Figure 3a below delivers water of density 1000 kg/m3 through a pipe of internal…

A: As per Bartleby's policy in case of multiple questions I can solve only first one. Please repost…

Q: Q5/ Pm = 900 kg/m3 Determine the flowrate through the pipe 2.5 m=h in Fig. Water 0.08 m

Q: fan delivers 283.2 m³/min of air with a density of 1.2 kg/m³ through a duct 5.08 cm 08 cm at the…

Q: A fan draws 2.42 m^3 per second of air at a static pressure of 2.54 cm water through a duct 300 mm…

Q: 8. An open water tank has two inlets and one outlet. The water flow rate through the two inlets are…

Q: If the static head of a fan which delivers 1,420 li/sec is 21.17 m. of air through a duct 30 cm in…

Q: Water flows through a horizontal pipe at a rate of 2.3 gal/s. The pipe consists of two sections of…

A: The flow rate of the water, The diameter at section 1, The diameter at section 2, The density of…

Q: The brake horsepower and water horsepower of a pump are determined to be 15 kW and 12 kW,…

Concept explainers

Hydronics

Question

The volume of air delivered by fan is 26 m^3/sec and 186 mm water gage.

The density of air is 1.5 kg/m^3 and the motor power needed to drive the fan is 48 kW.

Determine the fan efficiency in %

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

a fan draws 1.42m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan is 75% and air is measured at 25 degree celsius and 760 mm Hg
A fan draws 1.42 m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan mechanical is 70% and air is measured at 25 0C and 760 mmHg. Using p water formulaPw=
Water flows through a garden hose at a rate of 1 l/s. The upstream diameter of the hose is 2.5 cm, and the nozzle outlet has a diameter of 1 cm. Determine the upstream pressure (gage pressure).
A fluid enters a pipe at speed v1=0.1 m/s. the diameter of the tube is d=200mm and the fluid flowing through the pipe is mercury with a specific gravity of 13.6. the mass flow rate is
A horizontal water pipe diameter 15 cm converges to 7.5 cm diameter. If the pressures at the two sections are 4 kg/cm2, and 1.5 kg/cm2 respectively, calculate the flow rate of water.
A pitot-static tube is used to measure the velocity of air flowing through a duct. The manometer shows a difference in the head of 5.8 cm of water. If the density of air and water is 1.13 kg/m3 and 1000 kg/m3 determine the velocity of air. Assume the coefficient of the pitot tube as 0.98. Head in meters
At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is discharged into the atmosphere. The water level is 2 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) and the atmospheric pressure is 100 KPA. Determine the initial rate of water discharge (volumetric flow rate) from the tank, neglecting the effects of friction.
Water flows through a constricted pipe at a uniform rate. At one point, the diameter of the pipe is 0.056 m and the pressure is 5.7 x 104N/m2. At another point, 0.8 m higher than the previous point, the diameter is 0.023 m and the pressure is 1 X 104N/m2 . Calculate the velocities at the lower section and the upper section. Also calculate the rate of flow. Density of water = 1000 kg/m3.
Water from a reservoir is pumped over a hill through a 450 mm diameter and an absolute pressure of 1.0 kg/cm^2 is maintained at the summit. Water discharge is 30 m above the reservoir. The quantity pumped is 0.5 m^3/s. frictional losses is discharge and suction pipe, and pump is equivalent to 1.5 m. The speed of the pump is 800 rpm. Determine the following: A. Water power of the pump B. New value of discharge if the speed of the pump is increased to 1000 rpm C. New value of head if the speed of the pump is increased to 1000 rpm D.New value of power if the speed of the pump is increased to 1000 rpm
Water flows through an orifice at the vertical side of a closed cylindrical tank. The water level inside the tank remains constant at 3m and the pressure at the top of the tank is 30KPa. If the jet strikes the ground horizontally by 4.5m and below the vena contracta by 1m, determine the coefficient of velocity.
A boat moved by jet propulsion discharges water through a jet of area 0.02 m2; the water being drawn from inlet opening facing the direction of motion. The total drag is estimated to be 17.66 u2 N·m where u is the speed of the boat in metre per second. Take density of water at 1,020 kg/m3 and efficiency of the pump set is 78%. If the boat moves at 54 kilometers per hour, determine the following: A) Relative velocity of the jet in meters per second B) The power, in kilowatts, of the motor required to work the pumps C) Efficiency of propulsion, in %
A hydraulic motor has a displacement of 100 cm3 and operates with a pressure of 105 bars and a speed of 1700 rpm. If the actual flow rate consumed by the motor is 0.0025 m3/s and the actual torque delivered by the motor is 350 Nm. Calculate the overall efficiency of the motor. If the power supply to the motor is now reduced by 25%, what would happen to the overall efficiency of the pump? Support your answer with relevant calculations. You may propose your own scientific assumptions.